Search found 162 matches

by raffaplymouth
Wed Jan 18, 2017 11:06 am
Forum: Nitrous
Topic: Edelbrock nitrous controller on 4500 plate
Replies: 16
Views: 22164

Re: Edelbrock nitrous controller on 4500 plate

for this question : Not sure what the safety switch is, if that's a fuel pressure switch, pitch it. Those cause all kinds of problems.

yes is the fuel pressure minimal 5 psi safety switch
by raffaplymouth
Wed Jan 18, 2017 11:03 am
Forum: Nitrous
Topic: Edelbrock nitrous controller on 4500 plate
Replies: 16
Views: 22164

Re: Edelbrock nitrous controller on 4500 plate

Hi John .. no transbrake !!! yes i have copy your link for asking minimal percentual of start .... my last setting with 250 hp sprayed from launch with zero delay saw very good traction and no spin with 29 tires 9.32@148 1.42 60 ft 3800 lb with my ass , now i have 30.5 tires
by raffaplymouth
Wed Jan 18, 2017 5:20 am
Forum: Nitrous
Topic: Edelbrock nitrous controller on 4500 plate
Replies: 16
Views: 22164

Re: Edelbrock nitrous controller on 4500 plate

this is the wire that will be with the controller ! , let me know !
by raffaplymouth
Wed Jan 18, 2017 4:07 am
Forum: Nitrous
Topic: Edelbrock nitrous controller on 4500 plate
Replies: 16
Views: 22164

Re: Edelbrock nitrous controller on 4500 plate

read this : Trash Cans (non specific models) start to work around 20%, and reach full open at around 70% at 15 Hertz settings. Back to our calculator, that is a pulse width of .0133s at those settings. Technically they might be able to open at 16% if you drop down to 12 Hertz, that is the same pulse...
by raffaplymouth
Wed Jan 18, 2017 3:58 am
Forum: Nitrous
Topic: Edelbrock nitrous controller on 4500 plate
Replies: 16
Views: 22164

Re: Edelbrock nitrous controller on 4500 plate

yes , understand !! but which problem i can found on the car ?? under 50% ?? is better start at 50% or more ?
by raffaplymouth
Tue Jan 17, 2017 2:04 pm
Forum: Nitrous
Topic: Edelbrock nitrous controller on 4500 plate
Replies: 16
Views: 22164

Re: Edelbrock nitrous controller on 4500 plate

Sure ! I came make a ramp very quickly!! no problem.. I hope the engine will support this shock ! .. you can explaine me the problem of backpressure on the solenoids ??
by raffaplymouth
Mon Jan 16, 2017 1:14 pm
Forum: Nitrous
Topic: Edelbrock nitrous controller on 4500 plate
Replies: 16
Views: 22164

Re: Edelbrock nitrous controller on 4500 plate

therefore.. not improving with more hp ?? if track is not very good ??
by raffaplymouth
Mon Jan 16, 2017 1:48 am
Forum: Nitrous
Topic: Edelbrock nitrous controller on 4500 plate
Replies: 16
Views: 22164

Re: Edelbrock nitrous controller on 4500 plate

hi John , i don't understand this problem of backpressure , you think is better a short ramp in 1-2 sec ?? from 200 to 350 hp ?? before shifting ?? i would use my crossair blue plate and two solenoid for fuel and two for nitrous , but i don't want use two stages , this is my combo now : i have blue ...
by raffaplymouth
Thu Jan 12, 2017 2:28 pm
Forum: Nitrous
Topic: Edelbrock nitrous controller on 4500 plate
Replies: 16
Views: 22164

Re: Edelbrock nitrous controller on 4500 plate

anyone have some idea also for timing retard ? i have 7 al digital and 71900 Eddy nitrous controller .. thanks
by raffaplymouth
Wed Jan 11, 2017 2:51 pm
Forum: Nitrous
Topic: Edelbrock nitrous controller on 4500 plate
Replies: 16
Views: 22164

Edelbrock nitrous controller on 4500 plate

Hi ! i just buy the 71900 Nitrous Controller for my Cuda with 750 hp on motor and 250 of shot ... i had installed the crossplate 1 years ago with good success... my last setting with best time was 250 hp from launch .. and best ET 9.32.. i would install this controller for make a ramp like 200 hp sp...
by raffaplymouth
Thu Oct 27, 2016 2:35 am
Forum: Chassis and Suspension
Topic: 70 CUDA REAR END
Replies: 40
Views: 42713

Re: 70 CUDA REAR END

If you roll through the water towards the starting line and stop when you just pass the water puddle, the burnout will be more effective. In this video, at the beginning you can see the water puddle BEHIND the car and the burnout is done on dry ground. https://www.youtube.com/watch?v=KgWjLNiJ62s An...
by raffaplymouth
Thu Sep 22, 2016 9:29 am
Forum: Chassis and Suspension
Topic: 70 CUDA REAR END
Replies: 40
Views: 42713

Re: 70 CUDA REAR END

:attack:

This is very good info .. but I don't understand very well ... time of burnout .??? too water ?? after ??

my best 60 ft is 1.44....

is possible 1.38 ??
by raffaplymouth
Tue Sep 20, 2016 5:14 am
Forum: Chassis and Suspension
Topic: 70 CUDA REAR END
Replies: 40
Views: 42713

Re: 70 CUDA REAR END

some problem of traction on 60 ft