Search found 406 matches

by sunsation540
Tue Dec 10, 2013 10:29 pm
Forum: General BS
Topic: Tire Pressure Variation
Replies: 9
Views: 8406

Re: Tire Pressure Variation

we start with the tires .5 low first pass and recheck about 10-15 min after the first pass and set to running pressure, and usually don't have to adjust unless it gets real late or a huge oil down, we start .5 low after long periods of time. one hour or more.. this has worked well for us, however al...
by sunsation540
Wed Jun 30, 2010 10:41 pm
Forum: General BS
Topic: Ms. Daisy!!!!
Replies: 8
Views: 6360

Re: Ms. Daisy!!!!

doing my part for the planet recycling..
by sunsation540
Mon Jun 28, 2010 9:16 pm
Forum: General BS
Topic: Ms. Daisy!!!!
Replies: 8
Views: 6360

Re: Ms. Daisy!!!!

the fat girl can dance if you give her enough to drink LOL OOP'S
by sunsation540
Sun Apr 18, 2010 11:44 pm
Forum: Drivetrain
Topic: Brake problem
Replies: 23
Views: 13524

Re: Brake problem

Take your lines off the m/c and plug the ports. Then press the pedal and see if you have the same results if you do its a bad master if not plug off the front try again and so on. Also when bleeding did you tap the calipers with a rubber mallot? its recommended to get the "trapped" air out...
by sunsation540
Wed Mar 10, 2010 11:36 pm
Forum: Nitrous
Topic: We stumble on to something!!!!! No bottle heaters
Replies: 11
Views: 7164

Re: We stumble on to something!!!!! No bottle heaters

if you want to do something like this, take the n2o bottles to a scuba shop and have them pressure filled to 1100 @ 70* then chill the bottles down to 50 and you should have around 900, as the bottle temp rises so will the pressure however @100 deg you will loose the bottles as the pressure caps go ...
by sunsation540
Sat Mar 06, 2010 1:08 am
Forum: General BS
Topic: Question for those who have Plexiglass
Replies: 10
Views: 7469

Re: Question for those who have Plexiglass

I have some polycobarnate? what he said.. a shop here in okc molded it to my orignal glass sides and rear for proper curves, looks just like factory and the sides are installed to the regulators and roll up just fine,
by sunsation540
Sat Mar 06, 2010 1:05 am
Forum: Engine
Topic: How much hp did I pick up?
Replies: 8
Views: 5882

Re: How much hp did I pick up?

that deal should be good for 900 + or- 20 look for about 2 tenths increase,, have fun..but let us know.
by sunsation540
Thu Jan 28, 2010 8:07 pm
Forum: Engine
Topic: Solid Roller Warm Up
Replies: 13
Views: 9432

Re: Solid Roller Warm Up

basic crower comp and the howards and even some of the lower end pbm's, i think the isky red zones and crower hippo's are internal passaged,, just ways to move more oil to the top, we have some stuff with spray rails in the valve covers, and some marine blower stuff with piston oilers all kinds of,,...
by sunsation540
Thu Jan 28, 2010 7:34 pm
Forum: Engine
Topic: Solid Roller Warm Up
Replies: 13
Views: 9432

Re: Solid Roller Warm Up

i will try and make this short.. first take a lifter put it in the block ck where the oil hole is,, did you just figure out that the hole is in the flat part of the bore and doesen't hit the lube passage? reason for no oling,, the ones that have a bleed hole in the main channel will oil at all times...
by sunsation540
Mon Jan 25, 2010 10:19 pm
Forum: General BS
Topic: BBC parts for sale
Replies: 2
Views: 2870

Re: BBC parts for sale

pan is spoken for thanks
by sunsation540
Thu Jan 21, 2010 12:39 am
Forum: Chassis and Suspension
Topic: 9.99 Cert
Replies: 24
Views: 17857

Re: 9.99 Cert

door bar must pass through the mid of the upper arm.. however swing out door bars are legal to 8.50.. i'm fat and there!!
by sunsation540
Mon Jan 18, 2010 10:50 pm
Forum: Chassis and Suspension
Topic: Moroso tricks springs/ 69 Camaro
Replies: 14
Views: 12768

Re: Moroso tricks springs/ 69 Camaro

for what it's worth i agree with mike on this deal,, big tire cars need less stored energy and long soft springs can make to much bite.. and the gain of a typical 250 lb spring with one coil off is about 25 lbs per inch not a big deal.. try once buy once,
by sunsation540
Mon Jan 18, 2010 12:52 am
Forum: Engine
Topic: Solid Roller Warm Up
Replies: 13
Views: 9432

Re: Solid Roller Warm Up

you have to modify the lifter to move oil at lower rpm your springs and cold valve settings determin how long your stuff lives. take your valve covers off and let it idle you won't see any oil try this before you jump the gun you need to think this through! no oil to the rockers no oil through the l...
by sunsation540
Thu Dec 03, 2009 12:35 am
Forum: Nitrous
Topic: retard
Replies: 5
Views: 4724

Re: retard

did someone call my name RETARD 7531 also next year, dig 6 single stage retard now .tough on a 2 stage 500 hit!
by sunsation540
Mon Oct 19, 2009 9:13 pm
Forum: Engine
Topic: Used Pistons
Replies: 8
Views: 6729

Re: Used Pistons

tha's not a big deal and some scotch bright emery cloth will clean the edges up fine! THAT PISTON WILL RUN FOR YEARS it's a 427 no skirt loading light weight same ballancer and flywheel what's not to like! 2 cents