Where did the bars contact the springs?mytmouz wrote:Had a set of Mono leaf Landrums with a set of slapper bars on a 68 Nova and they bent right in front of both leaf spring perch mounting points very quickly...
Search found 187 matches
- Tue Dec 09, 2008 2:01 pm
- Forum: Chassis and Suspension
- Topic: Landrum?
- Replies: 11
- Views: 7782
Re: Landrum?
- Mon Dec 01, 2008 7:35 am
- Forum: In the Shop
- Topic: Garage heaters
- Replies: 16
- Views: 15524
Re: Garage heaters
I jut put a pellet stove in my 24x30, works great.
- Sat Nov 15, 2008 8:31 am
- Forum: Drivetrain
- Topic: Gun drilled axles
- Replies: 23
- Views: 20839
Re: Gun drilled axles
Yup i was looking on his site, that will most likely the route i will go, thanks!
Woohoo, they have a 35 spline spool!
Woohoo, they have a 35 spline spool!
- Fri Nov 14, 2008 2:31 pm
- Forum: Drivetrain
- Topic: Gun drilled axles
- Replies: 23
- Views: 20839
Re: Gun drilled axles
I will see what i can do for measurements, it may be a few weeks or so. I am building my new ''project'' garage right now so the car is sitting in my existing until the new one is done, then the fabrication begins. I will most likely make my own shock mounts and weld on the axle ends too. I am going...
- Fri Nov 14, 2008 1:01 pm
- Forum: Drivetrain
- Topic: Gun drilled axles
- Replies: 23
- Views: 20839
Re: Gun drilled axles
As this will be my first narrow job any info is good info. There are lockers available, just have a hard time spending the loot for one over a spool. I have power steering so it should not be as much of a nightmare on the street but alot of wasted rubber for sure, and i run soft tires for traction o...
- Fri Nov 14, 2008 11:28 am
- Forum: Drivetrain
- Topic: Gun drilled axles
- Replies: 23
- Views: 20839
Re: Gun drilled axles
I have been looking at this option aswell. I currently run moser 28spl c-clip axles for some added strength over stock as i have added nitrous. I am going to be narrowing the rear this winter and want to upgrade axles. The only way i can get any decent axle spline in a 8.5 10b is to go with the 33 (...
- Fri Nov 14, 2008 9:28 am
- Forum: Drivetrain
- Topic: Gun drilled axles
- Replies: 23
- Views: 20839
Re: Gun drilled axles
From their website: ''Moser Engineering, Inc. will, at its’ sole discretion replace or repair, free of cost, any part found not to be of ordered dimensional specifications, prior to assembly or use of the part. In addition, Moser Engineering, Inc. will replace their 33, 35, & 40 spline axles for...
- Fri Nov 14, 2008 9:21 am
- Forum: Engine
- Topic: Holley carb
- Replies: 31
- Views: 22261
Re: Holley carb
Fix the power valves issue, tweak the idle screws for better vacuum in/out of gear. That thing needs a bypass air circuit put in (shaker455), it helps with the idle tuning alot.
Up the base timing too.
Up the base timing too.
- Fri Oct 31, 2008 12:59 pm
- Forum: Engine
- Topic: block prep?
- Replies: 12
- Views: 7238
Re: block prep?
Can you not go to a splayed 4 bolt setup with chevies (converted from a 2 bolt)?
- Wed Oct 29, 2008 9:37 am
- Forum: General BS
- Topic: storing the car for winter
- Replies: 10
- Views: 6665
Re: storing the car for winter
I put some junk wheels on it and park it outside, thats it. I have done it that way for years.
This year i have a new garage so it will be spending the winter inside so i will be doing nothing other than empty the nitrous bottle.
This year i have a new garage so it will be spending the winter inside so i will be doing nothing other than empty the nitrous bottle.
- Tue Oct 21, 2008 7:09 am
- Forum: General BS
- Topic: Help with Nitrous
- Replies: 2
- Views: 2560
Re: Help with Nitrous
What is your fuel system now?
- Tue Oct 14, 2008 12:33 pm
- Forum: Chassis and Suspension
- Topic: caltracs VS ladder bars?
- Replies: 51
- Views: 42056
Re: caltracs VS ladder bars?
Hmm, that actually looks pretty good! I guess the height of the front has a big part in it too.
I dont think i could get my front that low with the tires i have (too wide), they rub every once and awhile as it is.
I dont think i could get my front that low with the tires i have (too wide), they rub every once and awhile as it is.
- Tue Oct 14, 2008 11:35 am
- Forum: Chassis and Suspension
- Topic: caltracs VS ladder bars?
- Replies: 51
- Views: 42056
Re: caltracs VS ladder bars?
Gearjammer- I have a few pics at home that i could put up when i get off work. Here is a few pics: http://www.putfile.com/biltit/albums Some launch vids here: http://www.putfile.com/biltit Basically i had to raise it to fit the tires because of my rim offset (15X8.5-3.75BS). I had a set of re-arched...
Re: pump cam
I run a modded 850DP on the street alot, works great.
- Sat Oct 11, 2008 3:05 pm
- Forum: Engine
- Topic: inconsistent fuel pressure
- Replies: 11
- Views: 7834
Re: inconsistent fuel pressure
The gauge is lying when its hot. The true setting is when everything is cold.
Your gauge may be bad.
Your gauge may be bad.