Keep tuning?

Suspension Tuning, Troubleshooting, Design and Discussion

Moderators: David Lemmond, Dave Morgan

Post Reply
Message
Author
User avatar
BracketNova
Posts: 618
Joined: Sat Apr 25, 2009 6:46 pm
Contact:

Keep tuning?

#1 Post by BracketNova » Sun Sep 07, 2014 10:39 pm

Wondering if I should keep tweaking my suspension or if this is pretty good for what I got?

I don't have a ton of dough in my setup. Cal-Tracs w/ their split monos. 3-way shocks back and front, 90/10s in the toolbox.

I tried 90/10s on the front and that was no good, it would pop the front up and when the front ran out of travel the rear tires spun. I put my 3 ways back on the front with the softest extension setting and it seems to hook well...but I'm wondering if I should try to tighten them more? Going up is not going forward right ;) I would like to get the front to settle down for the rest of the trip down the track as well - maybe the only way to accomplish that is with limiters?

Best run Saturday 1.4257 / 6.69
Earlier run, angle from front
Last edited by BracketNova on Wed Sep 10, 2014 10:48 pm, edited 1 time in total.
"I always compare drag racing to lighting $100 bills on fire, only it's more expensive." - Craig W.

Check out my website...
http://www.findmoneyraces.com


'71 Nova E85
6.69 @ 100.2 MPH 9/6/14
1.4257 60'
1700' DA

13:1 439 BBC
3330 lbs

bracketchev1221
Posts: 158
Joined: Fri Oct 11, 2013 7:59 pm
Location: Mountville PA

Re: Keep tuning?

#2 Post by bracketchev1221 » Wed Sep 10, 2014 8:00 am

An adjustable front travel limiter is always good to have. Tighten it down until the 60' falls off and leave it there. Any travel beyond what the car needs, does nothing but stick the nose up in the wind and screw with the front end alignment. I have used them in my car forever. Also, stiffen the front shock as much as you can as well. A 90/10 for example, is very soft on extension for travel, however the downside is the compression is very slow on them and it tends to keep the nose up longer. If 80/20, or even 70/30 works, it will get the nose down quicker.

User avatar
John_Heard
Site Admin
Posts: 5734
Joined: Thu May 12, 2005 11:20 am
Location: Resume Speed, Kansas
Contact:

Re: Keep tuning?

#3 Post by John_Heard » Thu Sep 11, 2014 4:14 pm

Does look like it might like slowing the front down a bit.

If you're building a limiter, try to design something that hits softer vs a hard bolt stop. Cable with rubber mount, or something would be nice.

User avatar
BracketNova
Posts: 618
Joined: Sat Apr 25, 2009 6:46 pm
Contact:

Re: Keep tuning?

#4 Post by BracketNova » Thu Sep 11, 2014 9:54 pm

My thoughts exactly John...I've always been leery of limiters. But, I'm thinking if I weld a door spring to the end of a bolt???
"I always compare drag racing to lighting $100 bills on fire, only it's more expensive." - Craig W.

Check out my website...
http://www.findmoneyraces.com


'71 Nova E85
6.69 @ 100.2 MPH 9/6/14
1.4257 60'
1700' DA

13:1 439 BBC
3330 lbs

User avatar
John_Heard
Site Admin
Posts: 5734
Joined: Thu May 12, 2005 11:20 am
Location: Resume Speed, Kansas
Contact:

Re: Keep tuning?

#5 Post by John_Heard » Thu Sep 11, 2014 10:37 pm

A cable would be a softer hit than a bolt through the top of the a-arm, I think a spring would be a bit too soft and probably kill it quick. Something like a rubber shock bushing where it attaches perhaps?

bracketchev1221
Posts: 158
Joined: Fri Oct 11, 2013 7:59 pm
Location: Mountville PA

Re: Keep tuning?

#6 Post by bracketchev1221 » Fri Sep 12, 2014 5:08 am

I think s&w race cars has a setup with a rubber bumper. I think that's where mine are from.

User avatar
wikd69
Posts: 2077
Joined: Sat Feb 23, 2008 12:42 pm
Location: Rocklin, CA
Contact:

Re: Keep tuning?

#7 Post by wikd69 » Fri Sep 12, 2014 10:29 pm

John_Heard wrote:Does look like it might like slowing the front down a bit.

If you're building a limiter, try to design something that hits softer vs a hard bolt stop. Cable with rubber mount, or something would be nice.
John - I'm using the old upside down 3/4" bolt trick in my upper a-arms. I would guess they come to a hard stop when I launch - I don't know that it has ever hurt me but I've thought about it. What would the hard stop do to the launch ?
1969 ProStreet Camaro RS Best 9.75@139 1.46 60'
Blown 427 BBC, TH400 w/Brake, Back-Half Ladderbar
Narrowed 12-Bolt, 4.10 Gears, Spool, Moser 33 Spline

http://www.marsh-racing.com/harrys_camaro-1.htm

User avatar
BracketNova
Posts: 618
Joined: Sat Apr 25, 2009 6:46 pm
Contact:

Re: Keep tuning?

#8 Post by BracketNova » Fri Sep 12, 2014 11:47 pm

Shock the system, causing the rear tires to unload. At least that's what I figure.
"I always compare drag racing to lighting $100 bills on fire, only it's more expensive." - Craig W.

Check out my website...
http://www.findmoneyraces.com


'71 Nova E85
6.69 @ 100.2 MPH 9/6/14
1.4257 60'
1700' DA

13:1 439 BBC
3330 lbs

User avatar
John_Heard
Site Admin
Posts: 5734
Joined: Thu May 12, 2005 11:20 am
Location: Resume Speed, Kansas
Contact:

Re: Keep tuning?

#9 Post by John_Heard » Sat Sep 13, 2014 9:33 am

Lots of cars use a hard bolt, including mine. Personally I'd like to use something that hits a bit softer, not sure if it would make much difference or not.

User avatar
John_Heard
Site Admin
Posts: 5734
Joined: Thu May 12, 2005 11:20 am
Location: Resume Speed, Kansas
Contact:

Re: Keep tuning?

#10 Post by John_Heard » Wed Sep 17, 2014 7:46 am

Saw this type of limiter last weekend. Looks to me like a person could make some variation on this to allow a softer hit. Not sure it's really necessary though, I think almost all cars are using a solid connection. Some use chain, cables or bolts though.
Attachments
20140913_111103.jpg

Post Reply

Who is online

Users browsing this forum: No registered users and 16 guests