New to site..lookin 4 guesses
Moderator: John_Heard
New to site..lookin 4 guesses
First off, hi to all. I'm lookin to see what ya think of this combo and what will it do in the 1/4? Thanks in advance for the input.
> ENGINE
>
> Mfg: Chevrolet
>
> Cubic Inch: 357" small block
>
> Compression Ratio: 13.58:1
>
>
>
> HEADS
>
> Mfg: Dart Pro 1 230cc, aluminum, 2.08 intake, 1.6 exhaust
>
> Ported (Yes or No): no
>
>
>
> INDUCTION
>
> Mfg: Dart
>
> Model: DRT-42411000
>
> Type: Single Plane
>
> Ported: Yes, matched to a Fel Pro 1206
>
> CAMSHAFT
>
> Mfg: Schneider
>
> P/N: custome grind (won't tell)
>
> solid flat tappet
>
> Intake Lift: .57
>
> Duration Advertised: 29?*
>
> Duration @ .050": 26?* ................104 L/S
>
> Rocker Ratio: 1.5
>
> Exhaust Lift: .6?
>
> Duration Advertised: 31?*
>
> Duration @ .050": 27?*................108 L/S
>
> Rocker Ratio: 1.5
>
> IGNITION
>
> Brand: MSD 7al 2, MSD billet dist. model # 85551, and the Blaster 3 coil.
> Taylor 8mm wires.
>
> Timing @ Idle:38
>
> Timing @ Full Advance: 38 Locked out
>
> EXHAUST
>
> Headers or Exhaust Manifolds: headers
>
> Primary Size: Hooker super Comp For G body
>
> Collector Size: 3"
>
> Pipe Diameter:
>
> Muffler Type: none
>
> Muffler Size: none
>
> FUEL SYSTEM
>
> Gas or Alcohol: Alcohol
>
> Pump Type: Belt drive
>
> Pump Size: "0"
>
> Carb: Ron's fuel 4 shooter 950
>
> Regulator or Bypass: 32 nozzle with 65 pill
>
> Type
>
> VEHICLE
>
> Type: 1978 Malibu
>
> Wt.: 3000 with driver and fuel
>
> Transmission: 1964 Powerglide, 1.76 first gear
>
> Number of Gears: 2
>
> Trans Brake (Yes or No): no
>
> Stall Speed: 5200-5700 Tci group 12
>
> Rear Tire Size: 28 x 9
>
> Gear Ratio: 5.14
>
> NITROUS: no
>
> No. of stages: n/a
>
> HP Rating: n/a
>
> Plate (Yes or No): n/a
>
> Nozzle (Yes or No): n/a
>
> Separate Fuel System (Yes or No): n/a
>
>
> ENGINE
>
> Mfg: Chevrolet
>
> Cubic Inch: 357" small block
>
> Compression Ratio: 13.58:1
>
>
>
> HEADS
>
> Mfg: Dart Pro 1 230cc, aluminum, 2.08 intake, 1.6 exhaust
>
> Ported (Yes or No): no
>
>
>
> INDUCTION
>
> Mfg: Dart
>
> Model: DRT-42411000
>
> Type: Single Plane
>
> Ported: Yes, matched to a Fel Pro 1206
>
> CAMSHAFT
>
> Mfg: Schneider
>
> P/N: custome grind (won't tell)
>
> solid flat tappet
>
> Intake Lift: .57
>
> Duration Advertised: 29?*
>
> Duration @ .050": 26?* ................104 L/S
>
> Rocker Ratio: 1.5
>
> Exhaust Lift: .6?
>
> Duration Advertised: 31?*
>
> Duration @ .050": 27?*................108 L/S
>
> Rocker Ratio: 1.5
>
> IGNITION
>
> Brand: MSD 7al 2, MSD billet dist. model # 85551, and the Blaster 3 coil.
> Taylor 8mm wires.
>
> Timing @ Idle:38
>
> Timing @ Full Advance: 38 Locked out
>
> EXHAUST
>
> Headers or Exhaust Manifolds: headers
>
> Primary Size: Hooker super Comp For G body
>
> Collector Size: 3"
>
> Pipe Diameter:
>
> Muffler Type: none
>
> Muffler Size: none
>
> FUEL SYSTEM
>
> Gas or Alcohol: Alcohol
>
> Pump Type: Belt drive
>
> Pump Size: "0"
>
> Carb: Ron's fuel 4 shooter 950
>
> Regulator or Bypass: 32 nozzle with 65 pill
>
> Type
>
> VEHICLE
>
> Type: 1978 Malibu
>
> Wt.: 3000 with driver and fuel
>
> Transmission: 1964 Powerglide, 1.76 first gear
>
> Number of Gears: 2
>
> Trans Brake (Yes or No): no
>
> Stall Speed: 5200-5700 Tci group 12
>
> Rear Tire Size: 28 x 9
>
> Gear Ratio: 5.14
>
> NITROUS: no
>
> No. of stages: n/a
>
> HP Rating: n/a
>
> Plate (Yes or No): n/a
>
> Nozzle (Yes or No): n/a
>
> Separate Fuel System (Yes or No): n/a
>
>
mid 10's when its sorted out ???
72 Malibu-Nov. '08-1.329-3.995-6.280@106.94-9.988@131.62
best 60ft to date- 1.319
http://www.dragtimes.com/1972-Chevrolet ... -5251.html
best 60ft to date- 1.319
http://www.dragtimes.com/1972-Chevrolet ... -5251.html
- John_Heard
- Site Admin
- Posts: 5734
- Joined: Thu May 12, 2005 11:20 am
- Location: Resume Speed, Kansas
- Contact:
Its all about the combo, if its all matched, you'll wonder how in the hell it went that fast, if its wrong, you'll tell everyone its a stock 350
72 Malibu-Nov. '08-1.329-3.995-6.280@106.94-9.988@131.62
best 60ft to date- 1.319
http://www.dragtimes.com/1972-Chevrolet ... -5251.html
best 60ft to date- 1.319
http://www.dragtimes.com/1972-Chevrolet ... -5251.html
I put the numbers in my Dyno & Drag simulator.
Should make about 625 hp @7300+ rpm, with over 500 lbs @ 5500.
It could run mid to low 10's, BUT you'll be at over 8000 rpm before the 1000 foot mark!!
CLICK! It just clicked EMcIllece, how are ya. I still say you need a lil taller gear and High 9's are yours.
It's run 10.88 @ 120.77 on gas, right. ---Bill.
Should make about 625 hp @7300+ rpm, with over 500 lbs @ 5500.
It could run mid to low 10's, BUT you'll be at over 8000 rpm before the 1000 foot mark!!
CLICK! It just clicked EMcIllece, how are ya. I still say you need a lil taller gear and High 9's are yours.
It's run 10.88 @ 120.77 on gas, right. ---Bill.
68 Camaro, 380ci, Procharger, G-force 5 speed, EFI, 7" 2 disc clutch, best ET 8.69 @159
Best 60' vid http://www.youtube.com/watch?v=1OLzx5jBo4w
Best 60' vid http://www.youtube.com/watch?v=1OLzx5jBo4w
what dyno & drag simulator do you use? im looking for one.sc68z28 wrote:I put the numbers in my Dyno & Drag simulator.
Should make about 625 hp @7300+ rpm, with over 500 lbs @ 5500.
It could run mid to low 10's, BUT you'll be at over 8000 rpm before the 1000 foot mark!!
CLICK! It just clicked EMcIllece, how are ya. I still say you need a lil taller gear and High 9's are yours.
It's run 10.88 @ 120.77 on gas, right. ---Bill.
Thanks
Stuart
what dyno & drag simulator do you use? im looking for one.SS8UUP wrote:
Thanks
Stuart[/quote]
Part of CompCams http://www.proracingsim.com/
---Bill.
68 Camaro, 380ci, Procharger, G-force 5 speed, EFI, 7" 2 disc clutch, best ET 8.69 @159
Best 60' vid http://www.youtube.com/watch?v=1OLzx5jBo4w
Best 60' vid http://www.youtube.com/watch?v=1OLzx5jBo4w
thanks a lot!sc68z28 wrote:Part of CompCams http://www.proracingsim.com/SS8UUP wrote:what dyno & drag simulator do you use? im looking for one.
Thanks
Stuart
---Bill.
Hey! Bingo! Starting to 2nd guess things though.sc68z28 wrote:I put the numbers in my Dyno & Drag simulator.
Should make about 625 hp @7300+ rpm, with over 500 lbs @ 5500.
It could run mid to low 10's, BUT you'll be at over 8000 rpm before the 1000 foot mark!!
CLICK! It just clicked EMcIllece, how are ya. I still say you need a lil taller gear and High 9's are yours.
It's run 10.88 @ 120.77 on gas, right. ---Bill.
Who is online
Users browsing this forum: Bing [Bot] and 26 guests