New to site..lookin 4 guesses

General Engine Discussion

Moderator: John_Heard

Post Reply
Message
Author
1320racer
Posts: 25
Joined: Fri Dec 08, 2006 6:43 pm

New to site..lookin 4 guesses

#1 Post by 1320racer » Sat Dec 09, 2006 12:03 am

First off, hi to all. I'm lookin to see what ya think of this combo and what will it do in the 1/4? Thanks in advance for the input.

> ENGINE
>
> Mfg: Chevrolet
>
> Cubic Inch: 357" small block
>
> Compression Ratio: 13.58:1
>
>
>
> HEADS
>
> Mfg: Dart Pro 1 230cc, aluminum, 2.08 intake, 1.6 exhaust
>
> Ported (Yes or No): no
>
>
>
> INDUCTION
>
> Mfg: Dart
>
> Model: DRT-42411000
>
> Type: Single Plane
>
> Ported: Yes, matched to a Fel Pro 1206
>
> CAMSHAFT
>
> Mfg: Schneider
>
> P/N: custome grind (won't tell)
>
> solid flat tappet
>
> Intake Lift: .57
>
> Duration Advertised: 29?*
>
> Duration @ .050": 26?* ................104 L/S
>
> Rocker Ratio: 1.5
>
> Exhaust Lift: .6?
>
> Duration Advertised: 31?*
>
> Duration @ .050": 27?*................108 L/S
>
> Rocker Ratio: 1.5
>
> IGNITION
>
> Brand: MSD 7al 2, MSD billet dist. model # 85551, and the Blaster 3 coil.
> Taylor 8mm wires.
>
> Timing @ Idle:38
>
> Timing @ Full Advance: 38 Locked out
>
> EXHAUST
>
> Headers or Exhaust Manifolds: headers
>
> Primary Size: Hooker super Comp For G body
>
> Collector Size: 3"
>
> Pipe Diameter:
>
> Muffler Type: none
>
> Muffler Size: none
>
> FUEL SYSTEM
>
> Gas or Alcohol: Alcohol
>
> Pump Type: Belt drive
>
> Pump Size: "0"
>
> Carb: Ron's fuel 4 shooter 950
>
> Regulator or Bypass: 32 nozzle with 65 pill
>
> Type
>
> VEHICLE
>
> Type: 1978 Malibu
>
> Wt.: 3000 with driver and fuel
>
> Transmission: 1964 Powerglide, 1.76 first gear
>
> Number of Gears: 2
>
> Trans Brake (Yes or No): no
>
> Stall Speed: 5200-5700 Tci group 12
>
> Rear Tire Size: 28 x 9
>
> Gear Ratio: 5.14
>
> NITROUS: no
>
> No. of stages: n/a
>
> HP Rating: n/a
>
> Plate (Yes or No): n/a
>
> Nozzle (Yes or No): n/a
>
> Separate Fuel System (Yes or No): n/a
>
>

User avatar
Bob West
Posts: 582
Joined: Sat Dec 24, 2005 1:39 pm
Location: Republic,Mo

#2 Post by Bob West » Sat Dec 09, 2006 9:15 am

mid 10's when its sorted out ???
72 Malibu-Nov. '08-1.329-3.995-6.280@106.94-9.988@131.62
best 60ft to date- 1.319
http://www.dragtimes.com/1972-Chevrolet ... -5251.html

User avatar
fishman
Posts: 56
Joined: Sun Nov 05, 2006 4:51 pm
Location: alberta,canada

#3 Post by fishman » Sat Dec 09, 2006 5:12 pm

i would probably lean more to the high 10's

User avatar
John_Heard
Site Admin
Posts: 5734
Joined: Thu May 12, 2005 11:20 am
Location: Resume Speed, Kansas
Contact:

#4 Post by John_Heard » Sat Dec 09, 2006 8:20 pm

10.90... What do we get if we guess correctly?

1320racer
Posts: 25
Joined: Fri Dec 08, 2006 6:43 pm

#5 Post by 1320racer » Sun Dec 10, 2006 9:55 am

Beyond wrote:10.90... What do we get if we guess correctly?
Nothin' , just askin.

User avatar
Bob West
Posts: 582
Joined: Sat Dec 24, 2005 1:39 pm
Location: Republic,Mo

#6 Post by Bob West » Sun Dec 10, 2006 9:58 am

Its all about the combo, if its all matched, you'll wonder how in the hell it went that fast, if its wrong, you'll tell everyone its a stock 350 ;)
72 Malibu-Nov. '08-1.329-3.995-6.280@106.94-9.988@131.62
best 60ft to date- 1.319
http://www.dragtimes.com/1972-Chevrolet ... -5251.html

User avatar
sc68z28
Posts: 189
Joined: Sun Jan 15, 2006 8:28 pm
Location: Riverside California

#7 Post by sc68z28 » Sun Dec 10, 2006 4:06 pm

I put the numbers in my Dyno & Drag simulator.
Should make about 625 hp @7300+ rpm, with over 500 lbs @ 5500.
It could run mid to low 10's, BUT you'll be at over 8000 rpm before the 1000 foot mark!!

:D CLICK! It just clicked EMcIllece, how are ya. I still say you need a lil taller gear and High 9's are yours.

It's run 10.88 @ 120.77 on gas, right. ---Bill.
68 Camaro, 380ci, Procharger, G-force 5 speed, EFI, 7" 2 disc clutch, best ET 8.69 @159
Best 60' vid http://www.youtube.com/watch?v=1OLzx5jBo4w

User avatar
SS8UUP
Posts: 66
Joined: Sun Feb 26, 2006 4:30 pm
Location: San Angelo, TEXAS

#8 Post by SS8UUP » Tue Dec 19, 2006 11:07 pm

sc68z28 wrote:I put the numbers in my Dyno & Drag simulator.
Should make about 625 hp @7300+ rpm, with over 500 lbs @ 5500.
It could run mid to low 10's, BUT you'll be at over 8000 rpm before the 1000 foot mark!!

:D CLICK! It just clicked EMcIllece, how are ya. I still say you need a lil taller gear and High 9's are yours.

It's run 10.88 @ 120.77 on gas, right. ---Bill.
what dyno & drag simulator do you use? im looking for one.

Thanks
Stuart

User avatar
sc68z28
Posts: 189
Joined: Sun Jan 15, 2006 8:28 pm
Location: Riverside California

#9 Post by sc68z28 » Wed Dec 20, 2006 11:00 am

SS8UUP wrote:
what dyno & drag simulator do you use? im looking for one.
Thanks
Stuart[/quote]

Part of CompCams http://www.proracingsim.com/

---Bill.
68 Camaro, 380ci, Procharger, G-force 5 speed, EFI, 7" 2 disc clutch, best ET 8.69 @159
Best 60' vid http://www.youtube.com/watch?v=1OLzx5jBo4w

User avatar
SS8UUP
Posts: 66
Joined: Sun Feb 26, 2006 4:30 pm
Location: San Angelo, TEXAS

#10 Post by SS8UUP » Wed Dec 20, 2006 6:27 pm

sc68z28 wrote:
SS8UUP wrote:what dyno & drag simulator do you use? im looking for one.
Thanks
Stuart
Part of CompCams http://www.proracingsim.com/

---Bill.
thanks a lot!

1320racer
Posts: 25
Joined: Fri Dec 08, 2006 6:43 pm

#11 Post by 1320racer » Sun Feb 04, 2007 2:49 pm

sc68z28 wrote:I put the numbers in my Dyno & Drag simulator.
Should make about 625 hp @7300+ rpm, with over 500 lbs @ 5500.
It could run mid to low 10's, BUT you'll be at over 8000 rpm before the 1000 foot mark!!

:D CLICK! It just clicked EMcIllece, how are ya. I still say you need a lil taller gear and High 9's are yours.

It's run 10.88 @ 120.77 on gas, right. ---Bill.
Hey! Bingo! Starting to 2nd guess things though.

Post Reply

Who is online

Users browsing this forum: No registered users and 20 guests