What you think?

General Nitrous Discussion

Moderator: John_Heard

Post Reply
Message
Author
jdgreentruck
Posts: 46
Joined: Fri Sep 19, 2008 4:47 pm
Location: Lyons, Texas

What you think?

#1 Post by jdgreentruck » Sun Nov 02, 2008 2:20 pm

I am thinking about putting Nitrous, NX system, on my truck. Here is what i got

350, .030 over 2 bolt main block with ARP main and head studs
Crane Cam Part #111431
Brownfeild Heads 2.08 intake and 1.60? exhaust Valves, 210 runners?
Keuth Black Hypereutectic Pistons #KB209
Comp. is around 12 to 1
Scat 6.00" Pro Comp Rods with 7/16 ARP bolts
Eagle crankshaft
Holley Strip Dominator Intake
Mallory Ignition
1.5 Rockers on Exhaust and 1.6 on Intake

How Much Nitrous you think it will take?????????
1992 S-10
355 sbc, Powerglide, 9" rear end
6.60s 100mph 1/8 mile

User avatar
rustbucket
Posts: 566
Joined: Tue Aug 15, 2006 6:36 pm
Location: central alabama

Re: What you think?

#2 Post by rustbucket » Sun Nov 02, 2008 2:31 pm

I wouldnt spray much with the kb pistons.
406sbc, powerglide, nitrous
http://youtube.com/watch?v=DssW5vc_t3k

User avatar
68 chevelle
Posts: 121
Joined: Sat Sep 16, 2006 5:05 pm
Location: MN

Re: What you think?

#3 Post by 68 chevelle » Sun Nov 02, 2008 7:27 pm

I wouldn't go over 150hp with those pistons.

jdgreentruck
Posts: 46
Joined: Fri Sep 19, 2008 4:47 pm
Location: Lyons, Texas

Re: What you think?

#4 Post by jdgreentruck » Wed Nov 05, 2008 7:36 pm

i was thinking about only putting 150 shot and that all. just like other to tell me what they think.
if change piston what you think about all others in motor

thanks all
1992 S-10
355 sbc, Powerglide, 9" rear end
6.60s 100mph 1/8 mile

User avatar
mytmouz
Posts: 643
Joined: Thu Sep 21, 2006 1:00 am
Location: Pelahatchie,MS

Re: What you think?

#5 Post by mytmouz » Thu Nov 06, 2008 12:05 am

I wouldn't put any on those pistons. I have seen lots of them with the top ring land missing in chunks with just street driving. A set of forged pistons would be good with the 150 shot and the rest of the set up...
Trucks are for haulin...

Image

ARAM
Posts: 136
Joined: Tue Jan 22, 2008 2:00 pm
Location: TEMECULA CA
Contact:

Re: What you think?

#6 Post by ARAM » Tue Nov 11, 2008 11:32 am

I had a set of those pistons in sbc 350 for about 4 years, Sprayed for two years . Worked good on a 150-180 shot for a long time.
Started putting 200 shot to and they lasted about 10 bottles
and the ring land broke off.
If you are not to greedy with the nos and make shure your timming and fuel pres, is good , You should be good. But if your buying a new set of pistons save the extra cash and buy forged pistons.
West coast heads up racing Pacific street car association
mean street #13

jdgreentruck
Posts: 46
Joined: Fri Sep 19, 2008 4:47 pm
Location: Lyons, Texas

Re: What you think?

#7 Post by jdgreentruck » Wed Nov 26, 2008 4:07 pm

ok i going to change to forged pistons, think motor bo ok with 150 to 200 shot?
like to change cam too maybe a roller anyone got any ideal. i am not a engine builder just a old hotroder
1992 S-10
355 sbc, Powerglide, 9" rear end
6.60s 100mph 1/8 mile

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest