Need help bad!! I am looking for a wiring schematic for doing my n2o set up. I'm gonna use my cheater kit and was wondering how to wire my relay. I'm not using a t-brake. Question is the built in window switch from my ignition box is rated at 10 amps neg. Can I use it to ground my relay for my solenoids. And then use the arming switch to turn on the relay. Then just break ground with my window switch to the relay ground??
Thanks alot. Stroker1
window switch and relay
Moderator: John_Heard
window switch and relay
'87 S10 stock suspension, Caltracs, 9" rearend, 1.82 Glide, 383 SBC,
Brodix Track1 Heads, 14:1 compression, 180 shot plate,
2" tube Hussler Headers, 1.38 60ft., 6.20 ET 1/8th, 109 MPH,
Still Tuning, more to come.
Brodix Track1 Heads, 14:1 compression, 180 shot plate,
2" tube Hussler Headers, 1.38 60ft., 6.20 ET 1/8th, 109 MPH,
Still Tuning, more to come.
Hello!! Man I really like this site for usefull information, but dang does it take a long time to get a response! Anybody got any advice??
'87 S10 stock suspension, Caltracs, 9" rearend, 1.82 Glide, 383 SBC,
Brodix Track1 Heads, 14:1 compression, 180 shot plate,
2" tube Hussler Headers, 1.38 60ft., 6.20 ET 1/8th, 109 MPH,
Still Tuning, more to come.
Brodix Track1 Heads, 14:1 compression, 180 shot plate,
2" tube Hussler Headers, 1.38 60ft., 6.20 ET 1/8th, 109 MPH,
Still Tuning, more to come.
http://www.chevyhiperformance.com/techa ... to_06.html
Here is a diagram and just substitute your window switch in place of the throttle switch.
Here is a diagram and just substitute your window switch in place of the throttle switch.
1974 Pontiac Ventura, 455P (9.5:1 comp.), 850DP, 3100 ''Tight'' 10'', 3.73's/28x13.5
Upgrading in June:
KRE 310cfm@.550 heads, 10.5 comp., hyd roller, 3800 tight 10'', better rear suspension.
Race Weight: 3750#'s
2007 best: 11.97 at 110 1.65 60ft.
Upgrading in June:
KRE 310cfm@.550 heads, 10.5 comp., hyd roller, 3800 tight 10'', better rear suspension.
Race Weight: 3750#'s
2007 best: 11.97 at 110 1.65 60ft.
Thanks alot guy!! That's exactly what I needed to know. My window switch will go at the end of that negative line. In other words it will be the source of ground for the relay, going through the FPSS and rull throttle switch.
That's awesome! Thanks
That's awesome! Thanks
'87 S10 stock suspension, Caltracs, 9" rearend, 1.82 Glide, 383 SBC,
Brodix Track1 Heads, 14:1 compression, 180 shot plate,
2" tube Hussler Headers, 1.38 60ft., 6.20 ET 1/8th, 109 MPH,
Still Tuning, more to come.
Brodix Track1 Heads, 14:1 compression, 180 shot plate,
2" tube Hussler Headers, 1.38 60ft., 6.20 ET 1/8th, 109 MPH,
Still Tuning, more to come.
Who is online
Users browsing this forum: No registered users and 32 guests