Fuel Cells & Plumbing Questions
Moderator: John_Heard
- John_Heard
- Site Admin
- Posts: 5734
- Joined: Thu May 12, 2005 11:20 am
- Location: Resume Speed, Kansas
- Contact:
I think the foam is a good idea to keep the fuel from sloshing around. It would probably work without it but might be a good idea to go ahead and get some for it. I've heard people say that it's safer, don't really have a good idea why it would be safer but might be something that I'm not thinking about.
Summit/jegs probably sells the foam blocks to put in them or any circle track shop.
Your pump will have to work harder if you mount the filter up like you're describing. Another option would be to make a frame and mount the cell higher in the trunk and have everything above the trunk floor pan. I've seen a lot of cars setup that way and it looks good.
Summit/jegs probably sells the foam blocks to put in them or any circle track shop.
Your pump will have to work harder if you mount the filter up like you're describing. Another option would be to make a frame and mount the cell higher in the trunk and have everything above the trunk floor pan. I've seen a lot of cars setup that way and it looks good.
-
- Posts: 36
- Joined: Fri May 20, 2005 11:12 pm
- Location: atlanta, GA
my only issue with that is the fact that the people I bought the car from cut a rectangular hole for the sump in the trunk pan. I can turn the filter inlet to the bottom and run a 90 degree fitting on it and the pump and just keep it right along the bottom of the trunk floor. Do you think that will help or will I still have troubles.
- John_Heard
- Site Admin
- Posts: 5734
- Joined: Thu May 12, 2005 11:20 am
- Location: Resume Speed, Kansas
- Contact:
I've never tried it that way but don't see why it wouldn't work out ok. Probably not the best way to do it, but for all practical purposes I doubt the pump will notice that it's a inch or two higher than the sump. On mine I just cut out a hole in the trunk floor for the pump so that only the motor on the pump sticks up into the trunk, the inlet is just below the trunk floor. I would avoid 90 degree fittings if you can, but if you do have to use them use the sweeping 90's like AN fittings have vs the hard 90's like a pipe elbow
Can you post some pics of your fuel cell/pump setup (from in the trunk and under the car)?Beyond wrote:I've never tried it that way but don't see why it wouldn't work out ok. Probably not the best way to do it, but for all practical purposes I doubt the pump will notice that it's a inch or two higher than the sump. On mine I just cut out a hole in the trunk floor for the pump so that only the motor on the pump sticks up into the trunk, the inlet is just below the trunk floor. I would avoid 90 degree fittings if you can, but if you do have to use them use the sweeping 90's like AN fittings have vs the hard 90's like a pipe elbow
- John_Heard
- Site Admin
- Posts: 5734
- Joined: Thu May 12, 2005 11:20 am
- Location: Resume Speed, Kansas
- Contact:
- John_Heard
- Site Admin
- Posts: 5734
- Joined: Thu May 12, 2005 11:20 am
- Location: Resume Speed, Kansas
- Contact:
- MOKANRACER
- Posts: 277
- Joined: Thu May 12, 2005 1:40 pm
- Location: S.E.Kansas
- Contact:
Floor mount
I had to do some cutting for clearance issues on my coil over mount,and just boxed around it when done. Also had to cut a hole and box around the sump to make it legal. No biggy,just purchased a sheet of 22 AWG mild steel and used a lot of it for floor and trunk floor patching any way. I know some make mounts coming off their rear down tubes of their cage.DriveWFO wrote:Thanks Roger and John! The trunk floor pan in my 74 (Nova) isn't flat, so I wonder if I'll have to fab up some type of mount for the fuel cell???
http://www.cardomain.com/ride/2658990 10.5 sec 130 mph 1.55 60ft with a 150 shot.- 11.17 122mph mtr pass at 1.58 60ft http://www.flickr.com/photos/kmc1955/se ... 663468991/ http://www.youtube.com/watch?v=4vAb2EUaE1U
Re: Floor mount
I need to get an IHRA rule book! Why did you have to box around the sump? Do you only have to do that if you're running a plastic fuel cell?MOKANRACER wrote:I had to do some cutting for clearance issues on my coil over mount,and just boxed around it when done. Also had to cut a hole and box around the sump to make it legal. No biggy,just purchased a sheet of 22 AWG mild steel and used a lot of it for floor and trunk floor patching any way. I know some make mounts coming off their rear down tubes of their cage.DriveWFO wrote:Thanks Roger and John! The trunk floor pan in my 74 (Nova) isn't flat, so I wonder if I'll have to fab up some type of mount for the fuel cell???
- MOKANRACER
- Posts: 277
- Joined: Thu May 12, 2005 1:40 pm
- Location: S.E.Kansas
- Contact:
Re: Floor mount
( The NHRA Rule Book (2004) under general requirments ,states that any fuel cell that protrudes thru the floor must be covered with a min .024 steel,or .032 aluminum.) Thats why I built my dropped sump cover.Just made it part of the trunk floor. It doesnt specify fuel cell material at all.DriveWFO wrote:I need to get an IHRA rule book! Why did you have to box around the sump? Do you only have to do that if you're running a plastic fuel cell?MOKANRACER wrote:I had to do some cutting for clearance issues on my coil over mount,and just boxed around it when done. Also had to cut a hole and box around the sump to make it legal. No biggy,just purchased a sheet of 22 AWG mild steel and used a lot of it for floor and trunk floor patching any way. I know some make mounts coming off their rear down tubes of their cage.DriveWFO wrote:Thanks Roger and John! The trunk floor pan in my 74 (Nova) isn't flat, so I wonder if I'll have to fab up some type of mount for the fuel cell???
http://www.cardomain.com/ride/2658990 10.5 sec 130 mph 1.55 60ft with a 150 shot.- 11.17 122mph mtr pass at 1.58 60ft http://www.flickr.com/photos/kmc1955/se ... 663468991/ http://www.youtube.com/watch?v=4vAb2EUaE1U
Who is online
Users browsing this forum: No registered users and 42 guests