Page 1 of 2

Engine is coming out of Chevelle for the dyno.

Posted: Tue Nov 12, 2013 9:34 am
by bracketchev1221
Due to a family issue, I didn't make it to the track for the last time. And being that I am helping Bruce go over his Camaro this winter, I figured I better find some power in mine. The car didn't quite show the power I thought it should have, so rather than waste money in entry and gas to go the track to test its going on the dyno. I have a few things I want to try and this will at least get me in the ball park. The car right now is still running its 9.0's to 9.1's. I have set it up to go to Jensen Technologies for the run. I am going after, timing, jetting, carb spacers, oil levels, and anything else I can throw at it. The car weighs 3170 with driver. Who wants to guess what it will make? I am hoping for 25 hp gain. I think its between 850-875 now.

Re: Engine is coming out of Chevelle for the dyno.

Posted: Tue Nov 12, 2013 11:27 am
by Bruce69Camaro
bracketchev1221 wrote:Due to a family issue, I didn't make it to the track for the last time. And being that I am helping Bruce go over his Camaro this winter, I figured I better find some power in mine.
That's right buddy...and you better keep an eye on the rearview mirror or wait, never mind, just keep looking out the front because you'll be seeing the back half of my car....LOL

Oh I'm sorry, I thought this was Mike Somebodyoranother, that I was talking too.

I'm guess 857hp.

Re: Engine is coming out of Chevelle for the dyno.

Posted: Fri Nov 15, 2013 8:18 am
by Craig W.
850-ish seems pretty reasonable.

I've seen the Supersucker spacers make a surprising difference on some manifolds. Not cheap but I've seen about 25 hp before. Not all engines will respond that way though.

I found a little over 20 hp on my motor after my 1050 Holley was maxed out by switching to a 1050 Quick Fuel. Too bad I didn't have the money to buy the carb that day.

Re: Engine is coming out of Chevelle for the dyno.

Posted: Fri Nov 15, 2013 9:37 am
by bracketchev1221
I do have a Wilson 1" 4 hole tapered spacer that I will be trying. I bought it years ago, and think it works. I have used it, but the Super Victor had a 1" open on it when I got it, and the intake porter put another 1" open on it. I think the 4 hole is a better spacer. I want to prove it. The other thing is I think I have a little bit of a reversion issue. The 4 hole may help that with the tapered bottom to redirect the gases. The safety plate under the dominator has some gray carbon on it, so there is nothing blocking the gases. I did loosen the intake lash .003 which should open the intake valve later to reduce overlap and reversion. I am trying to find an anti reversion plate, but you need the proper spacer to go with it. Otherwise the anti reversion plate is covered over by a regular open spacer. I just hate to spend $150 for a anti reversion plate if the 4 hole will do the same thing. I am space limited with the 4" cowl hood so I need to be careful of moving the carb too close to the hood.

Re: Engine is coming out of Chevelle for the dyno.

Posted: Mon Nov 18, 2013 11:04 am
by Bruce69Camaro
I'd just like to say, with all my help, Ray's motor is out of his car.

It was a tough job but I operated the engine hoist boom pretty darn good. I think I also helped put a bolt in the transmission bell housing through the mid plate and I know I did handle the front motor plate as well.

But I had a bigger job to do and that was taking care of his dog, Bisquit.

Ray just how did you do it without me all these years...... lmao2:

Guys if any of you are looking for a nice, factory Nova SS, he has one!

Re: Engine is coming out of Chevelle for the dyno.

Posted: Mon Nov 18, 2013 1:03 pm
by bracketchev1221
That was nothing, you have to see the act to get a T-400 in that car underneath alone. Putting the car on 4 jackstands and using 1 floor jack. Oh yeah, and the trans has to be slid under the car AND THEN on to the floor jack while under the car. As of right now, the tentative date for the dyno is Jan 7 2014.

Re: Engine is coming out of Chevelle for the dyno.

Posted: Mon Jan 06, 2014 6:51 pm
by bracketchev1221
The motor is in the truck and ready to go. I'll fill you in tomorrow with the numbers. I am looking for gains over peak power. I know how fast it goes. I need it to run quicker.

Re: Engine is coming out of Chevelle for the dyno.

Posted: Mon Jan 06, 2014 11:07 pm
by Hitchcock
Good luck. Let us know as soon as you can.

Re: Engine is coming out of Chevelle for the dyno.

Posted: Tue Jan 07, 2014 10:07 am
by Bruce69Camaro
After you get home, do I have to come over and help you put it back in???

Re: Engine is coming out of Chevelle for the dyno.

Posted: Tue Jan 07, 2014 10:56 am
by Bruce69Camaro
Ray just texted me, 1st pull of the day, 889HP.....

Re: Engine is coming out of Chevelle for the dyno.

Posted: Tue Jan 07, 2014 12:22 pm
by Mike Peters
Bruce69Camaro wrote: Oh I'm sorry, I thought this was Mike Somebodyoranother, that I was talking too.

I'm guess 857hp.

That's Mister Somebodyoranother to you!!! Doesn't really matter which Chevelle you line up against now does it lil bro? Results would be the same. Just handier for Ray to put you in your place. :-P

Re: Engine is coming out of Chevelle for the dyno.

Posted: Tue Jan 07, 2014 12:24 pm
by Bruce69Camaro
Second pull for Ray, 898HP....

Mikey my big bro....I got to admit, I would have nothing for Ray. My only chance would be that the sun hits my car just right and blinds him with a bright orange glow just enough to get me far out of the hole first to grab the win.

I'm just glad for him that he is getting these great numbers and I hope I'm there with him when he hits his first 8....

Re: Engine is coming out of Chevelle for the dyno.

Posted: Tue Jan 07, 2014 12:51 pm
by Bruce69Camaro
New number....903HP...

Re: Engine is coming out of Chevelle for the dyno.

Posted: Tue Jan 07, 2014 7:23 pm
by bracketchev1221
We ended up at

910 hp at 7100
776 tq at 5800.

Re: Engine is coming out of Chevelle for the dyno.

Posted: Tue Jan 07, 2014 7:33 pm
by Mike Peters
bracketchev1221 wrote:We ended up at

910 hp at 7100
776 tq at 5800.
Very nice! 8-) Good when you exceed expectations.