Chrysler Master Cyl
Moderator: John_Heard
- John_Heard
- Site Admin
- Posts: 5734
- Joined: Thu May 12, 2005 11:20 am
- Location: Resume Speed, Kansas
- Contact:
Chrysler Master Cyl
I'm making some changes to my brake system and looking at using the Chrysler / Dodge master cyl like all the race car shops sell. I read a post somewhere that a 1981 Dodge Ram D-150 with manual brakes has a 1-1/8 bore which is what Aerospace recommends for their 4 wheel discs.
Problem is going to the parts store the new and rebuilt ones are Cast Iron. Does anyone know what parts stores / manufacturers sells these in Aluminum now?
Problem is going to the parts store the new and rebuilt ones are Cast Iron. Does anyone know what parts stores / manufacturers sells these in Aluminum now?
My 1971 X275 Nova | Facebook
- John_Heard
- Site Admin
- Posts: 5734
- Joined: Thu May 12, 2005 11:20 am
- Location: Resume Speed, Kansas
- Contact:
chrys mast cyl
i need one of those too , i tried to cross that carquest number to napa and came up blank,
- John_Heard
- Site Admin
- Posts: 5734
- Joined: Thu May 12, 2005 11:20 am
- Location: Resume Speed, Kansas
- Contact:
possible find john , waiting to hear bck from whse
napa number 39178 has a 1.125 bore in it cking availabilityas we spk
Good number!!!!!!!!
John , that is a good number , got mine coming from napa , 39178 is the correct napa number . don,t know why it would'nt cross , but united , the folks that supply napa found it , thats her pal !....................................................................................
- John_Heard
- Site Admin
- Posts: 5734
- Joined: Thu May 12, 2005 11:20 am
- Location: Resume Speed, Kansas
- Contact:
Cool - You know I think I'm going to put a page up in the tech section with these PN's, some time down the road someone's sure to need these again.
My 1971 X275 Nova | Facebook
- John_Heard
- Site Admin
- Posts: 5734
- Joined: Thu May 12, 2005 11:20 am
- Location: Resume Speed, Kansas
- Contact:
Re: Good number!!!!!!!!
Was the NAPA one a aluminum body? By any chance do you guys remember the name brand that was on the Master Cyl Box / Manufacturer?moeraces wrote:John , that is a good number , got mine coming from napa , 39178 is the correct napa number . don,t know why it would'nt cross , but united , the folks that supply napa found it , thats her pal !....................................................................................
My 1971 X275 Nova | Facebook
- John_Heard
- Site Admin
- Posts: 5734
- Joined: Thu May 12, 2005 11:20 am
- Location: Resume Speed, Kansas
- Contact:
FYI - http://www.dragstuff.com/techarticles/R ... CylPN.html
If anyone comes up with other PN's models lemme know I'll add them to the page.
If anyone comes up with other PN's models lemme know I'll add them to the page.
My 1971 X275 Nova | Facebook
yes,,aluminum and made by united, supplier to napa
the master cyl is aluminum according to the part number , and is
- John_Heard
- Site Admin
- Posts: 5734
- Joined: Thu May 12, 2005 11:20 am
- Location: Resume Speed, Kansas
- Contact:
Did any of you guys have problems finding a fitting to work in the rear 1/2" outlet? I've been having an issue finding a fitting that has enough thread to seat on the internal flare before running out of thread. I've looked at most of the parts store's here and no luck, about ready to chamfer the 1/2 port some so the fitting will sit down deeper and seat.
My 1971 X275 Nova | Facebook
Who is online
Users browsing this forum: No registered users and 52 guests