Minitubbing the Ventura!!
Moderator: John_Heard
Minitubbing the Ventura!!
Figured there is a ton of info here so i would post up about my minitub/narrowing adventure ahead of me.
Feel free to post any info, questions, pics, etc.
Here is a start on another forum:
http://forums.performanceyears.com/foru ... p?t=586637
Keep in mind this is a STREET car still, i do some dragging but the street is my primary use.
I plan on minitubbing, relocating springs/shocks, and narrowing the diff with bearing locating ends instead of c-clip eliminators.
Already have the following:
28x13.5-15 MT ET Streets
On order 15x10 AR Classic TTII's 5.5BS
33 spline spool 8.5''
DSE offset shackles
Running multi-leaf springs
Probably going to order the DSE tubs and some double adj. shocks.
I may go with sliders instead of offset shackles, depends on ride height. I do not want to go too low, stock would be fine i think.
See my sig for a link to pics of current combo.
Ultimate goal is to lower the rear and fit wider tires so i can achieve better launches and more traction on the street especially.
BTW, i am looking for some pics of this tire width and possible height combos. I have been looking through the pics on this site but it can be tough to decifer some of it.
I am possibly a month out from beginning as i am currently finishing my garage before i can begin on the car.
Feel free to post any info, questions, pics, etc.
Here is a start on another forum:
http://forums.performanceyears.com/foru ... p?t=586637
Keep in mind this is a STREET car still, i do some dragging but the street is my primary use.
I plan on minitubbing, relocating springs/shocks, and narrowing the diff with bearing locating ends instead of c-clip eliminators.
Already have the following:
28x13.5-15 MT ET Streets
On order 15x10 AR Classic TTII's 5.5BS
33 spline spool 8.5''
DSE offset shackles
Running multi-leaf springs
Probably going to order the DSE tubs and some double adj. shocks.
I may go with sliders instead of offset shackles, depends on ride height. I do not want to go too low, stock would be fine i think.
See my sig for a link to pics of current combo.
Ultimate goal is to lower the rear and fit wider tires so i can achieve better launches and more traction on the street especially.
BTW, i am looking for some pics of this tire width and possible height combos. I have been looking through the pics on this site but it can be tough to decifer some of it.
I am possibly a month out from beginning as i am currently finishing my garage before i can begin on the car.
1974 Pontiac Ventura, 455P (9.5:1 comp.), 850DP, 3100 ''Tight'' 10'', 3.73's/28x13.5
Upgrading in June:
KRE 310cfm@.550 heads, 10.5 comp., hyd roller, 3800 tight 10'', better rear suspension.
Race Weight: 3750#'s
2007 best: 11.97 at 110 1.65 60ft.
Upgrading in June:
KRE 310cfm@.550 heads, 10.5 comp., hyd roller, 3800 tight 10'', better rear suspension.
Race Weight: 3750#'s
2007 best: 11.97 at 110 1.65 60ft.
Re: Minitubbing the Ventura!!
i can post you pictures of it being done if you like but i have to go through my thumb and hard drives but here is a few that i have on hand
this is a pic of some sliders getting installed on a 67 mustang
this is the front hangers moving in board
ok and heres 2 pic's of the minni tubs we gained almost 4 inches of tire
oh and his back seat still fits so the interior looks stock
rob
this is a pic of some sliders getting installed on a 67 mustang
this is the front hangers moving in board
ok and heres 2 pic's of the minni tubs we gained almost 4 inches of tire
oh and his back seat still fits so the interior looks stock
rob
best to date N/A 8.91@153
psca westcoast heads up racing open comp
67 Camaro RS/SS
BBC Powerglide 4800 stall 4.11 29.5x10.5W
http://www.chpdragracing.com
psca westcoast heads up racing open comp
67 Camaro RS/SS
BBC Powerglide 4800 stall 4.11 29.5x10.5W
http://www.chpdragracing.com
Re: Minitubbing the Ventura!!
Thanks, if you can post some pics that would be great.
1974 Pontiac Ventura, 455P (9.5:1 comp.), 850DP, 3100 ''Tight'' 10'', 3.73's/28x13.5
Upgrading in June:
KRE 310cfm@.550 heads, 10.5 comp., hyd roller, 3800 tight 10'', better rear suspension.
Race Weight: 3750#'s
2007 best: 11.97 at 110 1.65 60ft.
Upgrading in June:
KRE 310cfm@.550 heads, 10.5 comp., hyd roller, 3800 tight 10'', better rear suspension.
Race Weight: 3750#'s
2007 best: 11.97 at 110 1.65 60ft.
Re: Minitubbing the Ventura!!
I have a brand new set of sliders if any body needs them.
I ended up not useing them. This is a donation if any body will use them .
I ended up not useing them. This is a donation if any body will use them .
West coast heads up racing Pacific street car association
mean street #13
mean street #13
Re: Minitubbing the Ventura!!
Are they for monoleafs or multileafs?
1974 Pontiac Ventura, 455P (9.5:1 comp.), 850DP, 3100 ''Tight'' 10'', 3.73's/28x13.5
Upgrading in June:
KRE 310cfm@.550 heads, 10.5 comp., hyd roller, 3800 tight 10'', better rear suspension.
Race Weight: 3750#'s
2007 best: 11.97 at 110 1.65 60ft.
Upgrading in June:
KRE 310cfm@.550 heads, 10.5 comp., hyd roller, 3800 tight 10'', better rear suspension.
Race Weight: 3750#'s
2007 best: 11.97 at 110 1.65 60ft.
Re: Minitubbing the Ventura!!
sliders work on either doesn't matter if they are multi or mono i can believe someone hasn't taken them yet great item
best to date N/A 8.91@153
psca westcoast heads up racing open comp
67 Camaro RS/SS
BBC Powerglide 4800 stall 4.11 29.5x10.5W
http://www.chpdragracing.com
psca westcoast heads up racing open comp
67 Camaro RS/SS
BBC Powerglide 4800 stall 4.11 29.5x10.5W
http://www.chpdragracing.com
Re: Minitubbing the Ventura!!
Yup, i will take em if you ship to canada. I will pay the shipping no problem.
1974 Pontiac Ventura, 455P (9.5:1 comp.), 850DP, 3100 ''Tight'' 10'', 3.73's/28x13.5
Upgrading in June:
KRE 310cfm@.550 heads, 10.5 comp., hyd roller, 3800 tight 10'', better rear suspension.
Race Weight: 3750#'s
2007 best: 11.97 at 110 1.65 60ft.
Upgrading in June:
KRE 310cfm@.550 heads, 10.5 comp., hyd roller, 3800 tight 10'', better rear suspension.
Race Weight: 3750#'s
2007 best: 11.97 at 110 1.65 60ft.
Re: Minitubbing the Ventura!!
biltit PM sent your way.
West coast heads up racing Pacific street car association
mean street #13
mean street #13
Re: Minitubbing the Ventura!!
ARAM- sent one back.
1974 Pontiac Ventura, 455P (9.5:1 comp.), 850DP, 3100 ''Tight'' 10'', 3.73's/28x13.5
Upgrading in June:
KRE 310cfm@.550 heads, 10.5 comp., hyd roller, 3800 tight 10'', better rear suspension.
Race Weight: 3750#'s
2007 best: 11.97 at 110 1.65 60ft.
Upgrading in June:
KRE 310cfm@.550 heads, 10.5 comp., hyd roller, 3800 tight 10'', better rear suspension.
Race Weight: 3750#'s
2007 best: 11.97 at 110 1.65 60ft.
Re: Minitubbing the Ventura!!
chpcamaro- do you know what tubs those are? They look great! I was looking at detroit speed and eng. tubs but they are pricey!
I am open to any info, kits, etc. if someone knows of a good setup which is relatively low cost. I do not need a high dollar setup but something that works. I have decided double adj. shocks are a must but other than that i am still exploring options.
I am open to any info, kits, etc. if someone knows of a good setup which is relatively low cost. I do not need a high dollar setup but something that works. I have decided double adj. shocks are a must but other than that i am still exploring options.
1974 Pontiac Ventura, 455P (9.5:1 comp.), 850DP, 3100 ''Tight'' 10'', 3.73's/28x13.5
Upgrading in June:
KRE 310cfm@.550 heads, 10.5 comp., hyd roller, 3800 tight 10'', better rear suspension.
Race Weight: 3750#'s
2007 best: 11.97 at 110 1.65 60ft.
Upgrading in June:
KRE 310cfm@.550 heads, 10.5 comp., hyd roller, 3800 tight 10'', better rear suspension.
Race Weight: 3750#'s
2007 best: 11.97 at 110 1.65 60ft.
Re: Minitubbing the Ventura!!
we made those tubs i always make my own that way i know they fit it's pretty easy if you have a way to cut the sheet metal and a welder you can do it. if you decide you want to make your own e-mail me and i will help you through it
thanks
rob
chp474@aol.com
thanks
rob
chp474@aol.com
best to date N/A 8.91@153
psca westcoast heads up racing open comp
67 Camaro RS/SS
BBC Powerglide 4800 stall 4.11 29.5x10.5W
http://www.chpdragracing.com
psca westcoast heads up racing open comp
67 Camaro RS/SS
BBC Powerglide 4800 stall 4.11 29.5x10.5W
http://www.chpdragracing.com
Re: Minitubbing the Ventura!!
Hmm, i never thought of making my own. Might be able to do that. I will keep you in mind. I will know more once i get the car back in the shop and make a plan of attack.
1974 Pontiac Ventura, 455P (9.5:1 comp.), 850DP, 3100 ''Tight'' 10'', 3.73's/28x13.5
Upgrading in June:
KRE 310cfm@.550 heads, 10.5 comp., hyd roller, 3800 tight 10'', better rear suspension.
Race Weight: 3750#'s
2007 best: 11.97 at 110 1.65 60ft.
Upgrading in June:
KRE 310cfm@.550 heads, 10.5 comp., hyd roller, 3800 tight 10'', better rear suspension.
Race Weight: 3750#'s
2007 best: 11.97 at 110 1.65 60ft.
Re: Minitubbing the Ventura!!
You do nice work rob.chpcamaro wrote:we made those tubs i always make my own that way i know they fit it's pretty easy if you have a way to cut the sheet metal and a welder you can do it. if you decide you want to make your own e-mail me and i will help you through it
thanks
rob
chp474@aol.com
1969 ProStreet Camaro RS Best 9.75@139 1.46 60'
Blown 427 BBC, TH400 w/Brake, Back-Half Ladderbar
Narrowed 12-Bolt, 4.10 Gears, Spool, Moser 33 Spline
http://www.marsh-racing.com/harrys_camaro-1.htm
Blown 427 BBC, TH400 w/Brake, Back-Half Ladderbar
Narrowed 12-Bolt, 4.10 Gears, Spool, Moser 33 Spline
http://www.marsh-racing.com/harrys_camaro-1.htm
- BracketNova
- Posts: 618
- Joined: Sat Apr 25, 2009 6:46 pm
- Contact:
Re: Minitubbing the Ventura!!
Here's my .02 I'd like to add. If I did it all over again...
I used the factory tubs split the inner tub in the middle and added a steel strip to stretch the tub out. After I cut the tub down the middle, I cut the floor as close to the tub as I could and pulled it out. I removed what was left of the factory flange from the tub.
So here's my hind sight. I cut the floor back even with the notched frame...bad. I put the dressed tub against it and welded it in. This made it kinda ugly...fillet weld(I believe) covered up with a bunch of seam sealer. If I did it again instead of cutting the floor back to the frame I would leave an inch and bend it down and make a new flange to weld the tub to.
Greg
I used the factory tubs split the inner tub in the middle and added a steel strip to stretch the tub out. After I cut the tub down the middle, I cut the floor as close to the tub as I could and pulled it out. I removed what was left of the factory flange from the tub.
So here's my hind sight. I cut the floor back even with the notched frame...bad. I put the dressed tub against it and welded it in. This made it kinda ugly...fillet weld(I believe) covered up with a bunch of seam sealer. If I did it again instead of cutting the floor back to the frame I would leave an inch and bend it down and make a new flange to weld the tub to.
Greg
"I always compare drag racing to lighting $100 bills on fire, only it's more expensive." - Craig W.
Check out my website...
http://www.findmoneyraces.com
'71 Nova E85
6.69 @ 100.2 MPH 9/6/14
1.4257 60'
1700' DA
13:1 439 BBC
3330 lbs
Check out my website...
http://www.findmoneyraces.com
'71 Nova E85
6.69 @ 100.2 MPH 9/6/14
1.4257 60'
1700' DA
13:1 439 BBC
3330 lbs
-
- Posts: 4
- Joined: Fri Oct 07, 2011 4:57 pm
Re: Minitubbing the Ventura!!
You should be able to hook that thing up on small tires. Here is a video of my Ventura. It has a solid cam and steel factory d port heads. http://youtu.be/Twr7GCpKVic http://youtu.be/X1eowjSwr-oBILTIT wrote:Figured there is a ton of info here so i would post up about my minitub/narrowing adventure ahead of me.
Feel free to post any info, questions, pics, etc.
Here is a start on another forum:
http://forums.performanceyears.com/foru ... p?t=586637
Keep in mind this is a STREET car still, i do some dragging but the street is my primary use.
I plan on minitubbing, relocating springs/shocks, and narrowing the diff with bearing locating ends instead of c-clip eliminators.
Already have the following:
28x13.5-15 MT ET Streets
On order 15x10 AR Classic TTII's 5.5BS
33 spline spool 8.5''
DSE offset shackles
Running multi-leaf springs
Probably going to order the DSE tubs and some double adj. shocks.
I may go with sliders instead of offset shackles, depends on ride height. I do not want to go too low, stock would be fine i think.
See my sig for a link to pics of current combo.
Ultimate goal is to lower the rear and fit wider tires so i can achieve better launches and more traction on the street especially.
BTW, i am looking for some pics of this tire width and possible height combos. I have been looking through the pics on this site but it can be tough to decifer some of it.
I am possibly a month out from beginning as i am currently finishing my garage before i can begin on the car.
Who is online
Users browsing this forum: No registered users and 2 guests