Guys ...all your information, including those of wik69 are very important to me ... I will make a treasure, I think I delete the muffler and put 2 long tubes 18 " and then do the test marker, but my engine has too much power ... but now we must work on 60ft !! now we have 1.99, I'd like to 1.65...

http://img109.imageshack.us/img109/4843/dscn0293g.jpg Raffaele, Ok, so it just occurred to me... :scratch: You're running full street exhaust on the track, right ? I see you've welded your crank evac tubes into the exhaust outside the collectors so this might pose a problem, but I would drop the ex...

The one thing that bothers me, and it might just be the picture, but those slicks look awfully close to the leaf springs. So when will you be trying the new mods out? How about some fiberglass for the front end, like a hood and bumpers? i have fiberglass hood .. im looking for fiberglass bumper ..i...

Same way you would on a race car. Remove everything that isn't absolutely necessary. What does have to stay, lighten it. What I see in a quick glance - Power Brakes, convert to manual Cast iron water pump? Power Steering Wipers Inner Fenders? Lighter wheels Light weight brakes... etc. etc. Aluminum...

guys , look this :smt003 :smt003 http://www.youtube.com/watch?v=TF9IJljDMfk&feature=youtu.be Looking good :) Better hook ? yes look like better . When drive i see the hood nose !.. Better than before all this upgrading .. My friend told me the left front tire almost wheelie ..for perfect hook m...

guys , look this

http://www.youtube.com/watch?v=TF9IJljD ... e=youtu.be

http://img36.imageshack.us/img36/919/dscn0290l.jpg Uploaded with ImageShack.us http://img109.imageshack.us/img109/4843/dscn0293g.jpg Uploaded with ImageShack.us http://img838.imageshack.us/img838/3949/dscn0296f.jpg Uploaded with ImageShack.us http://img266.imageshack.us/img266/1052/dscn0298n.jpg Up...

Guys i have finished this work .. need only pinion angle adjust , i have buy the wedges on summitracing...

battery on the rear ok

swaybar removed ok

trim screw ok

evac system ok

subframe connector ok

Guys , i have decided for EVAC ( breather into headers ) look like good vacuum , you can see the video !!


http://www.youtube.com/watch?v=LzaBV1DUnb0

Your right, on some motors it may cause smoke on the high rpm's but my motor is not nearly what most of the motors are like here on this site. Here is something to think about, I just looked up the Moroso crankcase evac system and there was a footnote that said you shouldn't run this system if you ...

Just remember, this is on my car and what works on mine may not be the best for your car. On mine, I have a port on the back of my carb base plate, from there I go into the pcv on the one valve cover. On the other valve cover I use a Moroso breather. I have also seen guys run just a stock Mopar bre...

Bruce69Camaro wrote:Some people use them and some people don't.

I just use plain breathers and and a PVC valve on my car.

please give me a schema , you connect a breather to carburetor with PCV valve and a breather is open at air ??

raffaplymouth wrote:

Bruce69Camaro wrote:Some people use them and some people don't.

I just use plain breathers and and a PVC valve on my car.

Bruce wich is "plain "???

op sorry , i know plain breathers ... i would connect into exhaust for suck from crackcase and not dirty the engine compartment

Bruce69Camaro wrote:Some people use them and some people don't.

I just use plain breathers and and a PVC valve on my car.

Bruce wich is "plain "???

Guys , i have a question , i just work on modify the breathers , now i have breathers with hoses in air .. i have buy on summitracing a MR gasket kit " breathers into exhaust " , i have also two 45 degree hoses that welding on each headers ..2 valves and 2 hoses for connect in pcv valve co...