for this question : Not sure what the safety switch is, if that's a fuel pressure switch, pitch it. Those cause all kinds of problems.
yes is the fuel pressure minimal 5 psi safety switch
Search found 162 matches
- Wed Jan 18, 2017 11:06 am
- Forum: Nitrous
- Topic: Edelbrock nitrous controller on 4500 plate
- Replies: 16
- Views: 23648
- Wed Jan 18, 2017 11:03 am
- Forum: Nitrous
- Topic: Edelbrock nitrous controller on 4500 plate
- Replies: 16
- Views: 23648
Re: Edelbrock nitrous controller on 4500 plate
Hi John .. no transbrake !!! yes i have copy your link for asking minimal percentual of start .... my last setting with 250 hp sprayed from launch with zero delay saw very good traction and no spin with 29 tires 9.32@148 1.42 60 ft 3800 lb with my ass , now i have 30.5 tires
- Wed Jan 18, 2017 5:20 am
- Forum: Nitrous
- Topic: Edelbrock nitrous controller on 4500 plate
- Replies: 16
- Views: 23648
Re: Edelbrock nitrous controller on 4500 plate
this is the wire that will be with the controller ! , let me know !
- Wed Jan 18, 2017 5:19 am
- Forum: Nitrous
- Topic: Edelbrock nitrous controller on 4500 plate
- Replies: 16
- Views: 23648
- Wed Jan 18, 2017 4:07 am
- Forum: Nitrous
- Topic: Edelbrock nitrous controller on 4500 plate
- Replies: 16
- Views: 23648
Re: Edelbrock nitrous controller on 4500 plate
read this : Trash Cans (non specific models) start to work around 20%, and reach full open at around 70% at 15 Hertz settings. Back to our calculator, that is a pulse width of .0133s at those settings. Technically they might be able to open at 16% if you drop down to 12 Hertz, that is the same pulse...
- Wed Jan 18, 2017 3:58 am
- Forum: Nitrous
- Topic: Edelbrock nitrous controller on 4500 plate
- Replies: 16
- Views: 23648
Re: Edelbrock nitrous controller on 4500 plate
yes , understand !! but which problem i can found on the car ?? under 50% ?? is better start at 50% or more ?
- Tue Jan 17, 2017 2:04 pm
- Forum: Nitrous
- Topic: Edelbrock nitrous controller on 4500 plate
- Replies: 16
- Views: 23648
Re: Edelbrock nitrous controller on 4500 plate
Sure ! I came make a ramp very quickly!! no problem.. I hope the engine will support this shock ! .. you can explaine me the problem of backpressure on the solenoids ??
- Mon Jan 16, 2017 1:14 pm
- Forum: Nitrous
- Topic: Edelbrock nitrous controller on 4500 plate
- Replies: 16
- Views: 23648
Re: Edelbrock nitrous controller on 4500 plate
therefore.. not improving with more hp ?? if track is not very good ??
- Mon Jan 16, 2017 1:48 am
- Forum: Nitrous
- Topic: Edelbrock nitrous controller on 4500 plate
- Replies: 16
- Views: 23648
Re: Edelbrock nitrous controller on 4500 plate
hi John , i don't understand this problem of backpressure , you think is better a short ramp in 1-2 sec ?? from 200 to 350 hp ?? before shifting ?? i would use my crossair blue plate and two solenoid for fuel and two for nitrous , but i don't want use two stages , this is my combo now : i have blue ...
- Thu Jan 12, 2017 2:28 pm
- Forum: Nitrous
- Topic: Edelbrock nitrous controller on 4500 plate
- Replies: 16
- Views: 23648
Re: Edelbrock nitrous controller on 4500 plate
anyone have some idea also for timing retard ? i have 7 al digital and 71900 Eddy nitrous controller .. thanks
- Wed Jan 11, 2017 2:51 pm
- Forum: Nitrous
- Topic: Edelbrock nitrous controller on 4500 plate
- Replies: 16
- Views: 23648
Edelbrock nitrous controller on 4500 plate
Hi ! i just buy the 71900 Nitrous Controller for my Cuda with 750 hp on motor and 250 of shot ... i had installed the crossplate 1 years ago with good success... my last setting with best time was 250 hp from launch .. and best ET 9.32.. i would install this controller for make a ramp like 200 hp sp...
- Thu Oct 27, 2016 2:35 am
- Forum: Chassis and Suspension
- Topic: 70 CUDA REAR END
- Replies: 40
- Views: 45117
Re: 70 CUDA REAR END
If you roll through the water towards the starting line and stop when you just pass the water puddle, the burnout will be more effective. In this video, at the beginning you can see the water puddle BEHIND the car and the burnout is done on dry ground. https://www.youtube.com/watch?v=KgWjLNiJ62s An...
- Thu Sep 22, 2016 9:29 am
- Forum: Chassis and Suspension
- Topic: 70 CUDA REAR END
- Replies: 40
- Views: 45117
Re: 70 CUDA REAR END
This is very good info .. but I don't understand very well ... time of burnout .??? too water ?? after ??
my best 60 ft is 1.44....
is possible 1.38 ??
- Tue Sep 20, 2016 5:14 am
- Forum: Chassis and Suspension
- Topic: 70 CUDA REAR END
- Replies: 40
- Views: 45117
Re: 70 CUDA REAR END
some problem of traction on 60 ft
- Tue Sep 20, 2016 5:13 am
- Forum: Chassis and Suspension
- Topic: 70 CUDA REAR END
- Replies: 40
- Views: 45117