Tell me what I did!!!
Moderators: David Lemmond, Dave Morgan
Tell me what I did!!!
First of all, thanks to all of you for this wonderful forum. I am learning a ton!!
This is what I did. I took a hard hooking, good driving, stable 10.5 @ 127 car, (backhalved 4-link Olds) and ruined it. The front end height was about 4 inches above the height of the rear. Well, I decided to lower it and lower it I did. I removed a coil and then heated the spring for the final drop to level the car.
When I went back to the track, the car would hook but the right rear squatted and the left front rose, Violently. Car stayed squatted through the entire quarter so bad that it rubbed the top of the wheel tub.. At about 110 mph it became very squirrley, darting back and forth and I let out. I tried to stiffen the right rear shock but to no avail.
(correct me if I am wrong) I now realize that with changing th center of gravity, and the fact that I rotated the rear 4 link bars downward, I basically created a mess. My theory on this is, that I need to raise the front of the upper and bottom bar on the 4 link to compensate for this. My other big question is, should I raise the car back up or get aftermarket springs? Do I try to eliminate the bumpsteer problem that I have created or is it a product of my screwed up rear suspension?
I have a picture of the last launch where it bent the pass. side front four link bracket. Who can I send it to to post for me? I am going to the Richmond seminar to see Dave, but I really want to start working on the car now. Any help will be greatly appreciated.
Thanks
LEroy
This is what I did. I took a hard hooking, good driving, stable 10.5 @ 127 car, (backhalved 4-link Olds) and ruined it. The front end height was about 4 inches above the height of the rear. Well, I decided to lower it and lower it I did. I removed a coil and then heated the spring for the final drop to level the car.
When I went back to the track, the car would hook but the right rear squatted and the left front rose, Violently. Car stayed squatted through the entire quarter so bad that it rubbed the top of the wheel tub.. At about 110 mph it became very squirrley, darting back and forth and I let out. I tried to stiffen the right rear shock but to no avail.
(correct me if I am wrong) I now realize that with changing th center of gravity, and the fact that I rotated the rear 4 link bars downward, I basically created a mess. My theory on this is, that I need to raise the front of the upper and bottom bar on the 4 link to compensate for this. My other big question is, should I raise the car back up or get aftermarket springs? Do I try to eliminate the bumpsteer problem that I have created or is it a product of my screwed up rear suspension?
I have a picture of the last launch where it bent the pass. side front four link bracket. Who can I send it to to post for me? I am going to the Richmond seminar to see Dave, but I really want to start working on the car now. Any help will be greatly appreciated.
Thanks
LEroy
84 Olds Backhaved
496 "HAVIN FUN"
WV
496 "HAVIN FUN"
WV
- Dave Morgan
- Posts: 124
- Joined: Mon Jul 30, 2007 8:16 am
- Location: Lima, Ohio
LeRoy,
Wow, there are several things you could have done...
1) Cutting the coils out of the front springs made them stiffer. Not only is it harder for the car to pitch rotate rearward and transfer weight, when the car does pitch rotate, it is pivoting off the front suspension, not the center of the car.
2) You've got a good sense of the rear suspenion relationship, but you need to create a map of how to locate the instant center. Also understand there is a kinematic relationship, this has to do with the linkage itself. We'll get into how the torque is transfered through the drivetrain and to the tires.
3) Bumpsteer- you know you did something here. The good news is that you can fix it easily and cheaply (probably less than $2.00). The seminar I will present will not cover bumpsteer as most racers want me to focus on the rear suspension, so let's make sure we spend some private time together and I'll give you some tips.
4) Yes, you did change the CG height, but I doubt you fouled that up enough to make a huge difference. In either case, I'll show you how to locate it, both front-to-rear and height.
If you get in a hurry and want to work on the car before the seminar, just e-mail me at staaytuned@aol.com.
I hope this helps and I look forward to meeting you in Richmond.
Stay Tuned,
Dave
Wow, there are several things you could have done...
1) Cutting the coils out of the front springs made them stiffer. Not only is it harder for the car to pitch rotate rearward and transfer weight, when the car does pitch rotate, it is pivoting off the front suspension, not the center of the car.
2) You've got a good sense of the rear suspenion relationship, but you need to create a map of how to locate the instant center. Also understand there is a kinematic relationship, this has to do with the linkage itself. We'll get into how the torque is transfered through the drivetrain and to the tires.
3) Bumpsteer- you know you did something here. The good news is that you can fix it easily and cheaply (probably less than $2.00). The seminar I will present will not cover bumpsteer as most racers want me to focus on the rear suspension, so let's make sure we spend some private time together and I'll give you some tips.
4) Yes, you did change the CG height, but I doubt you fouled that up enough to make a huge difference. In either case, I'll show you how to locate it, both front-to-rear and height.
If you get in a hurry and want to work on the car before the seminar, just e-mail me at staaytuned@aol.com.
I hope this helps and I look forward to meeting you in Richmond.
Stay Tuned,
Dave
Author of "Doorslammers: The Chassisbook"
Drag Racing Chassis Seminars and Videos
Drag Racing Chassis Seminars and Videos
Yep, heat the spring, cut a coil and lost any chance of weight transfer, gotta have it unless you got all kinds of horsepower like JOHN .
72 Malibu-Nov. '08-1.329-3.995-6.280@106.94-9.988@131.62
best 60ft to date- 1.319
http://www.dragtimes.com/1972-Chevrolet ... -5251.html
best 60ft to date- 1.319
http://www.dragtimes.com/1972-Chevrolet ... -5251.html
Ok, I realize that I screwed the springs up. How then, would I lower the front of the car? without doing spring surgury. Also, before the lowering, the rear stiffened and I had no squat and it had weight transfer, hooked hard and went forward. Now, (I really need to show you this picture) it squats hard, still hooks but drives my wheel tub down on the top of the tire. I am assuming that my instant center point is now below the neutral line and it is squatting. What do I do about the spring situation? I am sure it will run high 9's but I am telling you, its so screwed up now that past 100 mph, it scares the heck out of me.
Can I send this pic to one of you more computer savy guys?
thanks
leroy
Can I send this pic to one of you more computer savy guys?
thanks
leroy
84 Olds Backhaved
496 "HAVIN FUN"
WV
496 "HAVIN FUN"
WV
- John_Heard
- Site Admin
- Posts: 5734
- Joined: Thu May 12, 2005 11:20 am
- Location: Resume Speed, Kansas
- Contact:
- Mike Peters
- Posts: 930
- Joined: Wed Oct 12, 2005 1:48 pm
- Location: Wichita, KS
Check the angle of your lower rear suspension links. If the bar is at a downward angle towards the chassis, this is probably why the body of the car is getting sucked down towards the tire. The rear end housing is trying drive itself over the chassis mounting point of the lower link. When it does this, the tire moves upward towards the body. The lower bar needs to be level or 1 to 2 degrees pointing down to the chassis. Once you lowered the front of the car, you changed ride height of the entire car along with the relationship between the suspension mounting points on the housing and suspension mounting points on the car. Not trying to insult you but, it sounds like you're in need of finding a chassis guy who has been down this road before to help you get it sorted out again. Making these adjustments without prior experience can be hazardous to your health.shookler wrote:Ok, I realize that I screwed the springs up. How then, would I lower the front of the car? without doing spring surgury. Also, before the lowering, the rear stiffened and I had no squat and it had weight transfer, hooked hard and went forward. Now, (I really need to show you this picture) it squats hard, still hooks but drives my wheel tub down on the top of the tire. I am assuming that my instant center point is now below the neutral line and it is squatting. What do I do about the spring situation? I am sure it will run high 9's but I am telling you, its so screwed up now that past 100 mph, it scares the heck out of me.
Can I send this pic to one of you more computer savy guys?
thanks
leroy
"If winning was easy, losers would be doing it"
- Mike Peters
- Posts: 930
- Joined: Wed Oct 12, 2005 1:48 pm
- Location: Wichita, KS
Also, Leroy, possibly part of the reason the car is handling so poorly at speed is because you're experiencing some roll steer. Roll steer is when the housing is trying to drive the car. This again, is possibly due to your housing trying to drive above the plane of thrust the lower suspension links give you when they are parallel to the track under power. Roll steer is also why really fast cars which use the South Side Machine bars philosophy usually need a driver's diaper at the big end. The housing tries to drive underneath the car instead of pushing it. Yours is possibly tring to drive over the car since I'm assuming your lower links are now pointed downward after you lowered your front end.shookler wrote:Ok, I realize that I screwed the springs up. How then, would I lower the front of the car? without doing spring surgury. Also, before the lowering, the rear stiffened and I had no squat and it had weight transfer, hooked hard and went forward. Now, (I really need to show you this picture) it squats hard, still hooks but drives my wheel tub down on the top of the tire. I am assuming that my instant center point is now below the neutral line and it is squatting. What do I do about the spring situation? I am sure it will run high 9's but I am telling you, its so screwed up now that past 100 mph, it scares the heck out of me.
Can I send this pic to one of you more computer savy guys?
thanks
leroy
But then, what do I know, I'm just a bicycle rider.............
"If winning was easy, losers would be doing it"
Trust me, your not insulting me. I am learning and soaking it all up. This is a whole different ballgame than my low 11 chevelle. I realized that with lowering it I messed it all up. I had it right to begin with, but, in the pursuit of fasterness, had to mess with it. Could I put it back to my prelowered ride height, measure the angles of the bars then try to duplicate the angles with the new ride height? I will move the bottom link to near level, but what about the top link?
I understand the theory and the neutral line and so forth, I just need to put it all into practice.
and what about the front springs??? Get rid of them? Replace them with what?
thanks
leroy
I understand the theory and the neutral line and so forth, I just need to put it all into practice.
and what about the front springs??? Get rid of them? Replace them with what?
thanks
leroy
84 Olds Backhaved
496 "HAVIN FUN"
WV
496 "HAVIN FUN"
WV
- John_Heard
- Site Admin
- Posts: 5734
- Joined: Thu May 12, 2005 11:20 am
- Location: Resume Speed, Kansas
- Contact:
My 1971 X275 Nova | Facebook
I am the one in the car, not the truck. What the pic does not show is the pass. rear (body) continues to go on down until the tub hits the tire. Front driver side ends up way in the air. Then about half track, the tire grows and rubs the tub again. I understand what you are saying about the way it is trying to drive over itself, but the part that really got me was that it drove the entire quarter like that.
Thanks for posting that pic, it is all much appreciated.
By the way, I didnt build the car, I bought it as a project form another guy that had to get out from under it. I have no idea why the front end was that high. I do know that it did run very well that way though.
I just want to fix it, and understand how I fixed it.
thanks again
leroy
Thanks for posting that pic, it is all much appreciated.
By the way, I didnt build the car, I bought it as a project form another guy that had to get out from under it. I have no idea why the front end was that high. I do know that it did run very well that way though.
I just want to fix it, and understand how I fixed it.
thanks again
leroy
84 Olds Backhaved
496 "HAVIN FUN"
WV
496 "HAVIN FUN"
WV
- sunsation540
- Posts: 406
- Joined: Sun Aug 20, 2006 11:32 pm
- Location: Moore OK.
- Mike Peters
- Posts: 930
- Joined: Wed Oct 12, 2005 1:48 pm
- Location: Wichita, KS
When you worked on the front spring it may have changed the preload in the car that was helping, sort of. I would put in the Anti roll bar and have less preload it in. If you want the front lower put in a lighter spring but dont let it go into coil bind. Moroso trick springs work well if its a stock control arm maybe the 212 if its light.
2007 HotRod's Drag Week 2007 SB/NA Champ
9.95@134, 1.30 60' Stock Susp. Drag Radials
5 Days 5 Tracks make one Weak
9.95@134, 1.30 60' Stock Susp. Drag Radials
5 Days 5 Tracks make one Weak
-
- Posts: 24
- Joined: Wed Nov 21, 2007 4:16 pm
- Location: NY
Who is online
Users browsing this forum: No registered users and 28 guests