It's Tubbed...Finally

Suspension Tuning, Troubleshooting, Design and Discussion

Moderators: David Lemmond, Dave Morgan

Post Reply
Message
Author
User avatar
5448
Posts: 38
Joined: Tue Oct 17, 2006 12:43 pm
Location: North Branch, MN

It's Tubbed...Finally

#1 Post by 5448 » Mon Apr 09, 2012 9:05 pm

Finally making progress again on the minitub project, so I had to share some photos. Spent some quality time in the garage over the long weekend, and have the tubs welded in. Now the project sheet is down to about 10 pages to get the car back to the track again!
Plan is to have it back out by the end of May.
I added up the hours on this project - roughly 60 hours to prep, notch the frame, plate what was left, and trim and install the tubs.
Next up is finishing gusset straps for the ladder bar mounts, additional tubing to brace the front crossmember, and finish off the floor.
Then on to mounting the fuel cell and plumbing the new fuel system, and finally paint in the trunk and some carpet inside.
The car has been apart for about a year and a half, side tracked by work schedules last fall and over the winter.
It will be good to have it all back together and running again, to say the least!
Eric
Attachments
Tub1.jpg
Tub7.jpg
Tub6.jpg

User avatar
BracketNova
Posts: 618
Joined: Sat Apr 25, 2009 6:46 pm
Contact:

Re: It's Tubbed...Finally

#2 Post by BracketNova » Mon Apr 09, 2012 11:07 pm

That should make some extra room :thumb:
"I always compare drag racing to lighting $100 bills on fire, only it's more expensive." - Craig W.

Check out my website...
http://www.findmoneyraces.com


'71 Nova E85
6.69 @ 100.2 MPH 9/6/14
1.4257 60'
1700' DA

13:1 439 BBC
3330 lbs

71 chevy
Posts: 156
Joined: Mon Nov 02, 2009 10:23 pm

Re: It's Tubbed...Finally

#3 Post by 71 chevy » Tue Apr 10, 2012 12:51 am

nice work man.

User avatar
John_Heard
Site Admin
Posts: 5734
Joined: Thu May 12, 2005 11:20 am
Location: Resume Speed, Kansas
Contact:

Re: It's Tubbed...Finally

#4 Post by John_Heard » Tue Apr 10, 2012 7:25 am

Good deal, that's a big project I bet you're glad to be wrapping it up.

joe69Z
Posts: 55
Joined: Mon Oct 03, 2011 10:37 am
Location: Kinston N.C.

Re: It's Tubbed...Finally

#5 Post by joe69Z » Fri Apr 13, 2012 10:17 am

5448 wrote:Finally making progress again on the minitub project, so I had to share some photos. Spent some quality time in the garage over the long weekend, and have the tubs welded in. Now the project sheet is down to about 10 pages to get the car back to the track again!
Plan is to have it back out by the end of May.
I added up the hours on this project - roughly 60 hours to prep, notch the frame, plate what was left, and trim and install the tubs.
Next up is finishing gusset straps for the ladder bar mounts, additional tubing to brace the front crossmember, and finish off the floor.
Then on to mounting the fuel cell and plumbing the new fuel system, and finally paint in the trunk and some carpet inside.
The car has been apart for about a year and a half, side tracked by work schedules last fall and over the winter.
It will be good to have it all back together and running again, to say the least!
Eric
Great lookig job!

User avatar
supernova
Posts: 2552
Joined: Sat Feb 02, 2008 7:35 pm
Location: Ft.Worth Tx

Re: It's Tubbed...Finally

#6 Post by supernova » Fri Apr 13, 2012 11:57 am

Nice! :thumb:

It's a lot of work ain't it? :scratch: :scratch: :scratch: but you got it done! :mrgreen: :mrgreen: :mrgreen:
Blackhoodmafia!!!! :mrgreen: :mrgreen:

1972 Nova SS
572 C.I. BBC

Best to date: 1/8
et: 5.28
mph: 134
new wt. 3340 lbs

User avatar
5448
Posts: 38
Joined: Tue Oct 17, 2006 12:43 pm
Location: North Branch, MN

Re: It's Tubbed...Finally

#7 Post by 5448 » Fri Apr 13, 2012 7:44 pm

Ha! You're not kidding! It all seemed so straightforward when I started cutting things out!
I'm definitely learning a lot as I go.
To begin with, my car had a portion of another car welded in to it at some point before I got it. The drivers rear trunk floor is all from another car. It didn't line up well, and had lots of horrible torch cut seams and patch panels. I didn't realize just how bad it was until I pulled the gas tank and cut off some of the patch panels.
The first thing I had to do was cut all the spot welds and patches out, reposition the floor, then trim and reweld. I took over 10 lbs. of overlapping metal out from that alone.
Once that was squared up, I could start with the actual tub portion.
I had a set of old Hoosier 29x12's that I used for all my mock up - even with the aggressive frame notching, they were pretty tight, width-wise. The section width was larger than what I calculated they would be on a 12" rim - I calculated 14.3", but they measured 15" at 15 psi.
I had already decided on Goodyear and ordered a set of 29x12's. I had calculated 14.2" section width, and they came out to 14.25" at 15 psi. So I gained .75" of section width, which will let me put the car down as low as I want.
I also switched directions on suspension last summer; originally I was going to keep the leaf springs, but decided to put ladder bars in instead.
To get the car low, I'm going to have to trim out a lot of floor to make clearance. My next step is to make templates and cut some more!
I ordered some light indoor/outdoor carpet today to finish everything off.
I also ordered a new package tray and some interior trim. I just about fell over when the parts total was $81, and shipping was $55! :shock: Apparently, the cardboard package tray can fall apart at any time, because it is shipped double oversize for protection. :roll: I checked three suppliers, and all shipped the same way. So no pressure when I cut holes for the rear down bars!
Oh, well, at least progress is being made, and the end is on the horizon!
The fab is a lot of fun, and I have a list of things I'd do differently next time, but it will feel good to make a pass again!
Eric

Post Reply

Who is online

Users browsing this forum: No registered users and 5 guests