4 link, driveshaft angle confusion
Moderators: David Lemmond, Dave Morgan
-
- Posts: 16
- Joined: Thu May 22, 2014 9:48 pm
4 link, driveshaft angle confusion
I have 68 Camaro rear half with a 4 link that uses a ladder bar frame. 30" tall tires ( forgot who makes it). Built the car myself and just got it running. BB 482 700hp pump gas. Engine and Trans are in the factorylocation. Doing some pinion angle adjustment. This is what I got.
Trans 2 degrees down
Driveshaft is running up hill 5 degrees.....
Rear of driveshaft is 2.5 inchs higher at the rear
I was told that driveshaft so be running down hill to rearend. So at first I put rear pinion 3 degrees up to compensate for a -1 degree of pinion angle. Is this right?
Or should I put pinion 1 degree down regardless of Trans or driveshaft.
I don't know how it ended up like this car is almost stock ride height.
Need some true help. Thanks
Trans 2 degrees down
Driveshaft is running up hill 5 degrees.....
Rear of driveshaft is 2.5 inchs higher at the rear
I was told that driveshaft so be running down hill to rearend. So at first I put rear pinion 3 degrees up to compensate for a -1 degree of pinion angle. Is this right?
Or should I put pinion 1 degree down regardless of Trans or driveshaft.
I don't know how it ended up like this car is almost stock ride height.
Need some true help. Thanks
-
- Posts: 165
- Joined: Wed Nov 22, 2006 6:10 pm
- Location: Lancaster CA.
Re: 4 link, driveshaft angle confusion
you don't want negative pinion. With a 4 link car i dont think you need much pinion angle 1-2 degrees?
Trans 2 degrees down, rearend 0 degrees would be 2 positive. My driveshaft also goes up from trans to rearend, depends how low the car is in the back as well as the rearend type. dana 60 / 12 bolt drive higher in the case than a 9 inch
Trans 2 degrees down, rearend 0 degrees would be 2 positive. My driveshaft also goes up from trans to rearend, depends how low the car is in the back as well as the rearend type. dana 60 / 12 bolt drive higher in the case than a 9 inch
3100 lb N/A SBC 8.81 @ 152 http://www.youtube.com/watch?v=wkww0xwoZXE
-
- Posts: 16
- Joined: Thu May 22, 2014 9:48 pm
Re: 4 link, driveshaft angle confusion
Thanks for the response
It's a 12 bolt. What I had was trans 3 degrees down and Pinion was 4° up. To give me a negative one degree pinion total. 3 - 4 = -1. But with the driveshaft running uphill at 5° , which would give me Universal joint angles over what I have read is to much. (Transmission yoke down 3° driveshaft up 5° universal articulation 8. (Right? I think.).
As far as the driveshaft running up to the rearend, from what I have tried to figure out is that even if you have the trans and pinion degrees the same, (but opposite), angles. The driveshaft running up to pinion is already passed the straight line your trying to get underload. ( pinion will not try to climb down ring gear, it climbs up to meet the straight line. This sounds a lot better in my head. Make any sense?
So what I have done is lowered the front of the engine about 1° which raised the trans mission tail shaft up 1° (which now the tail shaft is 2° pointing down) Then raised the ride height of the car 1 inch (which I don't like would like to keep the car lower) and reset my my pinion angle. So what I have now is trans tail shaft yoke 2° down, driveshaft at almost 0, pinion 3° up.
Need some reassurance does this sound good?
Thanks again any more info's always helpful
It's a 12 bolt. What I had was trans 3 degrees down and Pinion was 4° up. To give me a negative one degree pinion total. 3 - 4 = -1. But with the driveshaft running uphill at 5° , which would give me Universal joint angles over what I have read is to much. (Transmission yoke down 3° driveshaft up 5° universal articulation 8. (Right? I think.).
As far as the driveshaft running up to the rearend, from what I have tried to figure out is that even if you have the trans and pinion degrees the same, (but opposite), angles. The driveshaft running up to pinion is already passed the straight line your trying to get underload. ( pinion will not try to climb down ring gear, it climbs up to meet the straight line. This sounds a lot better in my head. Make any sense?
So what I have done is lowered the front of the engine about 1° which raised the trans mission tail shaft up 1° (which now the tail shaft is 2° pointing down) Then raised the ride height of the car 1 inch (which I don't like would like to keep the car lower) and reset my my pinion angle. So what I have now is trans tail shaft yoke 2° down, driveshaft at almost 0, pinion 3° up.
Need some reassurance does this sound good?
Thanks again any more info's always helpful
-
- Posts: 165
- Joined: Wed Nov 22, 2006 6:10 pm
- Location: Lancaster CA.
Re: 4 link, driveshaft angle confusion
Lets forget the driveshaft angle for a min, driveshaft just connects the trans to rearend.
2 degrees down on trans, 0 degrees on rearend gives you the 2 degrees you are looking for.
Here is some good info also http://www.markwilliams.com/driveshafttech.aspx
2 degrees down on trans, 0 degrees on rearend gives you the 2 degrees you are looking for.
Here is some good info also http://www.markwilliams.com/driveshafttech.aspx
3100 lb N/A SBC 8.81 @ 152 http://www.youtube.com/watch?v=wkww0xwoZXE
-
- Posts: 16
- Joined: Thu May 22, 2014 9:48 pm
Re: 4 link, driveshaft angle confusion
Sorry to be a pan. But when you say 2 degrees down at Trans, 0 degrees at pinion , gives me the 2 degrees im looking for.....
That's ? 2 degrees positive up? or neg down?
I keep reading with 4 link I need 1 degree neg (pinion down). In relation to driveshaft.
Also. You said your driveshaft travels up to rear end as well? And this is ok?
I think maybe I'm trying to understand 2 different theories
That's ? 2 degrees positive up? or neg down?
I keep reading with 4 link I need 1 degree neg (pinion down). In relation to driveshaft.
Also. You said your driveshaft travels up to rear end as well? And this is ok?
I think maybe I'm trying to understand 2 different theories
- Bruce69Camaro
- Posts: 1799
- Joined: Thu Jul 23, 2009 11:07 am
- Location: PA
Re: 4 link, driveshaft angle confusion
Here is what I used to set mine up: http://www.swracecars.com/Files/pdf/10_300_400.pdf
Scroll down to page 6, Instructions for locating the rear housing under the car.
My pinion angle might, if I remember correctly is like 1 degree up, which is basically what clutchdude is stating.
Hookdaddy who worked for S&W is a member here, let me see if I can get ahold of him to give more details on what I posted a link too.
Scroll down to page 6, Instructions for locating the rear housing under the car.
My pinion angle might, if I remember correctly is like 1 degree up, which is basically what clutchdude is stating.
Hookdaddy who worked for S&W is a member here, let me see if I can get ahold of him to give more details on what I posted a link too.
Those who think they know it all have no way of finding out they don't.........
![Head Scratch :scratch:](./images/smilies/icon_headscratch.gif)
Re: 4 link, driveshaft angle confusion
I'm still having problems visualizing a 4-link rear suspension on a ladder bar frame? Pinion angle on a 4-link is not nearly as important with as it was when early drag cars were using leaf springs and a pinion snubber. point the pinion at the rear of the trans and you're done.
Don Scholl
S&W Race Cars - retired
145H Super Comp
145Y Stock Eliminator & ET Brackets
S&W Race Cars - retired
145H Super Comp
145Y Stock Eliminator & ET Brackets
-
- Posts: 16
- Joined: Thu May 22, 2014 9:48 pm
Re: 4 link, driveshaft angle confusion
Thanks Don
What I have is a Alston pro street sub frame that has 4-link bars
(Ladder bar sub frame).
This is where I have it set.
Trans at 1.78 down. Pinion at 0.
What do you think?
Thanks.
What I have is a Alston pro street sub frame that has 4-link bars
(Ladder bar sub frame).
This is where I have it set.
Trans at 1.78 down. Pinion at 0.
What do you think?
Thanks.
Re: 4 link, driveshaft angle confusion
can you post a link to the Alston frame you are using?
Don Scholl
S&W Race Cars - retired
145H Super Comp
145Y Stock Eliminator & ET Brackets
S&W Race Cars - retired
145H Super Comp
145Y Stock Eliminator & ET Brackets
-
- Posts: 16
- Joined: Thu May 22, 2014 9:48 pm
Re: 4 link, driveshaft angle confusion
https://www.cachassisworks.com/p-1551-p ... overs.aspx
I have one of the first versions of this 4link set up. It only has 4-5 holes on the front mounts and they are straight vertical.
Took the car to the track last week it ran 10:70 at 129 miles an hour off the trailer 1 time ever after building the car 20 yrs. car hooked pretty good little tired chatter on Hoosier QuickTime street tires. I thought that was pretty good for just your average gearhead building a car by himself from scratch need a little more preload. And loosen up the shocks a little bit.
Car was set up with the 1.75 down on the trans and the rear in Pinion angle set at zero.
I have one of the first versions of this 4link set up. It only has 4-5 holes on the front mounts and they are straight vertical.
Took the car to the track last week it ran 10:70 at 129 miles an hour off the trailer 1 time ever after building the car 20 yrs. car hooked pretty good little tired chatter on Hoosier QuickTime street tires. I thought that was pretty good for just your average gearhead building a car by himself from scratch need a little more preload. And loosen up the shocks a little bit.
Car was set up with the 1.75 down on the trans and the rear in Pinion angle set at zero.
Re: 4 link, driveshaft angle confusion
OK - now I'm with you. Forget that it once had a ladder bar frame in it. That's a true 4-link with equal length bars, it's just that the 4-link front brackets are mounted to the crossmember instead of to the frame rail. Sounds like the trans and pinion angle are ok. The limiting factor for now will be the adhesion of the street type tire. Start with some tire pressure adjustments and go from there. Keep us posted. 129 mph is big time for a 10.70 ET - that's showing me 10 teen potential
Don Scholl
S&W Race Cars - retired
145H Super Comp
145Y Stock Eliminator & ET Brackets
S&W Race Cars - retired
145H Super Comp
145Y Stock Eliminator & ET Brackets
-
- Posts: 16
- Joined: Thu May 22, 2014 9:48 pm
Re: 4 link, driveshaft angle confusion
Finally have a chance to get get back to ya.
Thanks for all your help. Gotta get it scaled and maybe move the IC alittle.
Car went 10.01 135mph. Pump gas ,exhaust, street tire. Then broke the gear. Still has a lot in it. Be spraying it with slicks soon.
Thanks for all your help. Gotta get it scaled and maybe move the IC alittle.
Car went 10.01 135mph. Pump gas ,exhaust, street tire. Then broke the gear. Still has a lot in it. Be spraying it with slicks soon.
Who is online
Users browsing this forum: No registered users and 107 guests