One of the most critical areas of a automatic race car
Moderator: Marty Chance
-
Jamie V
- Posts: 6
- Joined: Tue Nov 24, 2009 8:11 pm
#1
Post
by Jamie V » Sun Dec 19, 2010 8:22 pm
Marty, I'm planning on buying this converter from a buddy of mine for my Ford C6. It's a bolt together that you made for him some years back. I had him send me a picture of the stamped info on it so you could tell me about it before I buy it to make sure it will be close for what I need.
Thanks
Jamie V
![Image](http://www.delvallo.net/gallery/data/582/Chance_Converter1.jpg)
-
Marty Chance
- Posts: 193
- Joined: Fri Sep 19, 2008 6:34 am
- Location: Cheney, KS
#2
Post
by Marty Chance » Mon Dec 20, 2010 7:02 am
9.5" bolt together built 5/17/06 for an F2 procharged lightning with a 370ci motor
what did you want to put it in?
-
Jamie V
- Posts: 6
- Joined: Tue Nov 24, 2009 8:11 pm
#3
Post
by Jamie V » Mon Dec 20, 2010 6:54 pm
Marty, I have a ford lightning also but a totally different setup. I have a N/A 438" small block. I'm not sure of the motors horsepower but the truck weighs 3560 with me in it and has gone 9.88@135. with a best 60' of 1.32. The current converter is an Art Carr 9.5" spragless converter. It will trans break with no two step to 5800. The converter I have seems to work pretty well but I think I'm leaving some on the table up stairs with it being spragless.
Does that converter in the picture have a sprag (diode) in it? and if so is it one of your "extreme duty mechanical diodes" or a regular diode?
-
Marty Chance
- Posts: 193
- Joined: Fri Sep 19, 2008 6:34 am
- Location: Cheney, KS
#4
Post
by Marty Chance » Tue Dec 21, 2010 10:56 am
that converter is too tight for your n/a motor.
it has the regular 5 strut diode
If it is cheap enough i can redesign it for you, but you would have about $500 in changing it. Now if you want to throw some nitrous on it , then it would work pretty good for you
-
Jamie V
- Posts: 6
- Joined: Tue Nov 24, 2009 8:11 pm
#5
Post
by Jamie V » Tue Dec 21, 2010 4:28 pm
What do you estimate it will stall to the way it is N/A? I have considered spraying it down the road but what amount of nitrous are you thinking it would be right for?
Thanks again
Jamie
-
Marty Chance
- Posts: 193
- Joined: Fri Sep 19, 2008 6:34 am
- Location: Cheney, KS
#6
Post
by Marty Chance » Wed Dec 22, 2010 5:52 am
N/A the converter will stall about 3800 to 4200 with your 4" stroke motor. As for the amount of nitrous the more the better as this is a very tight converter for your combo.
-
Jamie V
- Posts: 6
- Joined: Tue Nov 24, 2009 8:11 pm
#7
Post
by Jamie V » Wed Dec 22, 2010 8:53 am
Would it effect you stall estimate that the stroke is 4.100"? The motor is 4.100 stroke 4.125 bore.
Also what did you estimate it would stall behind that procharged motor it was designed for?
-
Marty Chance
- Posts: 193
- Joined: Fri Sep 19, 2008 6:34 am
- Location: Cheney, KS
#8
Post
by Marty Chance » Wed Dec 22, 2010 9:17 am
it may stall slightly higher with the longer stroke.
Who is online
Users browsing this forum: No registered users and 77 guests