I thought it might be the carb at first but am leaning toward converter. Leaving at 4200 the car acts like the converter is tight, gets out a ways then accelerates real quick. On the shift at 6700 it drops to around 5,200 and stays there for a bit and then starts accelerating, almost like it's too loose. Not to mention it very inconsistent. On the burnout it doesn't seem turn the tires over until the secondaries open and rpm gets pretty high. The converter is an 8" borrowed from a car that it stalled around 5600 with same size engine but more comp, cam, and head.
Thanks, Keith
Could converter be bad?
Moderator: Marty Chance
Could converter be bad?
8.90@149 and 3,000lb, no Juice, no boost!
-
- Posts: 193
- Joined: Fri Sep 19, 2008 6:34 am
- Location: Cheney, KS
Re: Could converter be bad?
possible that the sprag in the converter is broke or it may simply be too tight for your motor. where does your motor make peak HP and peak TQ?
Neal Chance Racing Converters
Home of the World's Fastest Automatic Doorslammers!
www.racingconverters.com
Home of the World's Fastest Automatic Doorslammers!
www.racingconverters.com
Re: Could converter be bad?
Thanks Marty, I haven't had the engine dynoed but am guessing peak tq at around 5000 and hp around 6500. 406, 11.5:1, 260/264@.050", ported vi Jr heads, 1.80 glide, 4.56 w/32 tall tire, around 2850lbs.
Thanks, Keith
Thanks, Keith
8.90@149 and 3,000lb, no Juice, no boost!
-
- Posts: 193
- Joined: Fri Sep 19, 2008 6:34 am
- Location: Cheney, KS
Re: Could converter be bad?
Actually sounds like the converter may be just a little too tight. (as your description of the shift recovery) what rpm do you cross the finish line with this converter?
Neal Chance Racing Converters
Home of the World's Fastest Automatic Doorslammers!
www.racingconverters.com
Home of the World's Fastest Automatic Doorslammers!
www.racingconverters.com
Re: Could converter be bad?
To tell the truth, it's hard to say because the et is all over the place and the finish line rpm varies. I've only run 1/8 mile and it varies how long it stays at the shift rpm until it starts climbing again. It did mph between 96-104!
Thanks
Thanks
8.90@149 and 3,000lb, no Juice, no boost!
-
- Posts: 193
- Joined: Fri Sep 19, 2008 6:34 am
- Location: Cheney, KS
Re: Could converter be bad?
OK if the mph varies 96-104 something is way wrong.
? converter fins pulled ,blocking fluid flow worse on some passes than others? (check for debris in fluid)
? tire spin you dont know is happening?
? weak ignition system?
just a few of the gremlins that mey be haunting you. You may have to do process of elimination. change one thing at a time until you find the problem.
? converter fins pulled ,blocking fluid flow worse on some passes than others? (check for debris in fluid)
? tire spin you dont know is happening?
? weak ignition system?
just a few of the gremlins that mey be haunting you. You may have to do process of elimination. change one thing at a time until you find the problem.
Neal Chance Racing Converters
Home of the World's Fastest Automatic Doorslammers!
www.racingconverters.com
Home of the World's Fastest Automatic Doorslammers!
www.racingconverters.com
Re: Could converter be bad?
Thanks Marty, I'm putting my converter from my 555in and see what happens. It stalled at 6200 in that motor I'm hoping for around 5000 in the 406.
Thanks, Keith
Thanks, Keith
8.90@149 and 3,000lb, no Juice, no boost!
Who is online
Users browsing this forum: No registered users and 1 guest