Hello all, it's been a while.
I'm new to nitrous and relatively new to the motor in my car (specs in sig). I bought the motor/trans/convertor from another buick guy who went 11.0x @122 with it, in a very similar car to mine, NA. Motor made 590ish flywheel. Engine builder told me to run 34° locked, and do.
I have a nx single entry crossbar on the way. It has tune ups for 50-300. I will only be spraying 150 of it with an NOS Mini progressive, due to rod limitations. I have some tuning to do as it appears rich and has not been tuned at this altitude. So that will come first before spray. the plugs are filthy right now from idle/street driving. So i dont have a good point of reference. They are NGK R5671A-8. Ill probably tune it up with another set of 8s on NA before i swap to colder. Then work on the nitrous.
The question is, does this seem cold already? Nitrous express recommends 2 ranges colder, which would be a R5671A-10. The previous owner and builder said they were going to try nitous late in the season, ran into problems and didn't. Think they left cold plugs in it from that? Edelbrock recommends a 5 range, but these heads have a good deal of work, and this motor makes a bit more steam than they were intended to. Getting ready order a few sets from rock auto, and wondering what to buy. 9s... 10s..?
Also, how do think this will work with my combo? Cam is:
Intake. Exaust
Valve lift. .566. .543
Adv. Dur. 277° 290°
Dur@ .050" 251° 260°
Open Close
INT 17.5 BTDC 53.5 ABDC
EXH 66.0 BBDC 14.0 ATDC
Lobe Separation: 112°
Degreed to 108°
Any help would be appreciated.
ngk heat range on 150 shot
Moderator: John_Heard
ngk heat range on 150 shot
Rob
'70 GS Stage 1, 466 BBB, 11:1,wiesco pistons, stock rod, ported Edelbrock heads, 1.55 rollers, single plain intake, 950 Quickfuel, aeromotive ss pump, TH400, 9" PTC converter, 3.90 12bolt, NOS Mini, NX Single entry Crossbar
'70 GS Stage 1, 466 BBB, 11:1,wiesco pistons, stock rod, ported Edelbrock heads, 1.55 rollers, single plain intake, 950 Quickfuel, aeromotive ss pump, TH400, 9" PTC converter, 3.90 12bolt, NOS Mini, NX Single entry Crossbar
- Bruce69Camaro
- Posts: 1799
- Joined: Thu Jul 23, 2009 11:07 am
- Location: PA
Re: ngk heat range on 150 shot
According to most nos kit manufacturers, they recommend to step down at least 1 heat range for a 100 - 150 shot and 2 heat ranges over 150 shot.
I was running NGK R5673-7 on my 150 shot.
I was running NGK R5673-7 on my 150 shot.
Those who think they know it all have no way of finding out they don't.........
Re: ngk heat range on 150 shot
That's what NX recommended. Problem is, i suspect what i have is too cold to start with. I don't have a good point of reference to go two colder from. If i simply go two colder i am at a 10 for a 150 shot. So i am trying to find a point of reference from someone doing something similar.Bruce69Camaro wrote: ↑Mon Jan 13, 2020 11:03 am According to most nos kit manufacturers, they recommend to step down at least 1 heat range for a 100 - 150 shot and 2 heat ranges over 150 shot.
I was running NGK R5673-7 on my 150 shot.
You say you run a 7. What compression and fuel are you running? I'm 11:1 and plan on 100 or better fuel.
Rob
'70 GS Stage 1, 466 BBB, 11:1,wiesco pistons, stock rod, ported Edelbrock heads, 1.55 rollers, single plain intake, 950 Quickfuel, aeromotive ss pump, TH400, 9" PTC converter, 3.90 12bolt, NOS Mini, NX Single entry Crossbar
'70 GS Stage 1, 466 BBB, 11:1,wiesco pistons, stock rod, ported Edelbrock heads, 1.55 rollers, single plain intake, 950 Quickfuel, aeromotive ss pump, TH400, 9" PTC converter, 3.90 12bolt, NOS Mini, NX Single entry Crossbar
- Bruce69Camaro
- Posts: 1799
- Joined: Thu Jul 23, 2009 11:07 am
- Location: PA
Re: ngk heat range on 150 shot
My compression was around 11.5:1 and I was running 110 octane.
Those who think they know it all have no way of finding out they don't.........
Re: ngk heat range on 150 shot
Ok, that makes it relative for sure. Thanks!
Rob
'70 GS Stage 1, 466 BBB, 11:1,wiesco pistons, stock rod, ported Edelbrock heads, 1.55 rollers, single plain intake, 950 Quickfuel, aeromotive ss pump, TH400, 9" PTC converter, 3.90 12bolt, NOS Mini, NX Single entry Crossbar
'70 GS Stage 1, 466 BBB, 11:1,wiesco pistons, stock rod, ported Edelbrock heads, 1.55 rollers, single plain intake, 950 Quickfuel, aeromotive ss pump, TH400, 9" PTC converter, 3.90 12bolt, NOS Mini, NX Single entry Crossbar
Who is online
Users browsing this forum: No registered users and 2 guests