Dash fabrication
Moderator: John_Heard
Re: Dash fabrication
But you didn't make the entire frame on the CNCpro70z28 wrote:
Re: Dash fabrication
Nope, I didn't want to spend that kind of money. I've got about 200 bux in this including bolts & anvils. Not counting my time since this is considered a hobby. I need to save some of the aluminum for "Z" parts.
Re: Dash fabrication
Just about done with this deal. Got all the steel parts painted black & made a plywood rack for the lower anvils. All that's left is to dial in the top anvil. Seems to have pulled the bottom in a little during the welding. A shim ought to bring it back into alignment. I tried it out and I'll be if it doesn't work. Time to get back on the "Z" now.
The plan was to make it light enough to carry around. Weighs 84 Lbs. including a set of anvils. My shoulder fits under the top arm so it's not bad taking it out & putting it in the wall receivers. I planned to put struts on the bottom arm but it seems to be pretty stable the way it is. If it becomes a problem I'll add that later. Don't want it any heavier than it has to be.
The plan was to make it light enough to carry around. Weighs 84 Lbs. including a set of anvils. My shoulder fits under the top arm so it's not bad taking it out & putting it in the wall receivers. I planned to put struts on the bottom arm but it seems to be pretty stable the way it is. If it becomes a problem I'll add that later. Don't want it any heavier than it has to be.
Re: Dash fabrication
Thats a gorgeous piece of work.
1969 ProStreet Camaro RS Best 9.75@139 1.46 60'
Blown 427 BBC, TH400 w/Brake, Back-Half Ladderbar
Narrowed 12-Bolt, 4.10 Gears, Spool, Moser 33 Spline
http://www.marsh-racing.com/harrys_camaro-1.htm
Blown 427 BBC, TH400 w/Brake, Back-Half Ladderbar
Narrowed 12-Bolt, 4.10 Gears, Spool, Moser 33 Spline
http://www.marsh-racing.com/harrys_camaro-1.htm
Re: Dash fabrication
Thanks wikd69. I had to try a scrap pc. of .080 aluminum just to see what it would do. Bare in mind I've never used one of these contraptions before so I'm sure it would turn out better with practice. I'm surprised how easy they are to use. I figured I'd get a workout pulling & pushin' the workpiece back & forth but it's so easy a caveman could do it.
Re: Dash fabrication
My problem is my lack of space perception - I don't think in three dimensions. Give me logical model to build, assimilate or describe and I'm your guy. I have this very large, constantly evolving technology model in my head and it covers lots and lots of territory. Put me in front of your English wheel, give me a piece of sheet metal and tell me to form a fender to fit a certain shape and I'll die on the vine <shrug>. I just don't do physical very well. I've always been in awe of those folks who can form and fashion flowing compound curve shapes, and produce identical copies, like for fender pairs or other shapes. I just don't grok it...pro70z28 wrote:Thanks wikd69. I had to try a scrap pc. of .080 aluminum just to see what it would do. Bare in mind I've never used one of these contraptions before so I'm sure it would turn out better with practice. I'm surprised how easy they are to use. I figured I'd get a workout pulling & pushin' the workpiece back & forth but it's so easy a caveman could do it.
1969 ProStreet Camaro RS Best 9.75@139 1.46 60'
Blown 427 BBC, TH400 w/Brake, Back-Half Ladderbar
Narrowed 12-Bolt, 4.10 Gears, Spool, Moser 33 Spline
http://www.marsh-racing.com/harrys_camaro-1.htm
Blown 427 BBC, TH400 w/Brake, Back-Half Ladderbar
Narrowed 12-Bolt, 4.10 Gears, Spool, Moser 33 Spline
http://www.marsh-racing.com/harrys_camaro-1.htm
Re: Dash fabrication
Just takes practice wikd69. One last shot, it fits in the void behind the door with the Bead Roller, Shrinker/Stretcher, Plannishing Hammer & Welding table when they aren't in use. So, I'm hardly loosing any floor space at all when it's all put away. I have to add one more receiver on the storage rack for the vise since I now have one more attachment than I do storage rack receivers. On normal days this space is just more or less a hallway to the back room where the CNC is (where I normally do sign work). I need this space open so I can get materials into the room and signs back out.
Re: Dash fabrication
O.K. Now I'm done. For sure. I'm in the sign biz' ..... I had to do it.....what can I say? lol.
- hugger73hatch
- Posts: 360
- Joined: Sun Oct 21, 2007 10:42 pm
Re: Dash fabrication
73 Nova Hatchback, 408 Small Block 13-1, Iron Heads, 6.972 @ 98.362, 1.468 60', 3450 lbs, still tuning
28 x 9 Slick, N/A
http://www.esquireservices.net
28 x 9 Slick, N/A
http://www.esquireservices.net
Re: Dash fabrication
Thats cool. Now, can you build me one ?pro70z28 wrote:O.K. Now I'm done. For sure. I'm in the sign biz' ..... I had to do it.....what can I say? lol.
1969 ProStreet Camaro RS Best 9.75@139 1.46 60'
Blown 427 BBC, TH400 w/Brake, Back-Half Ladderbar
Narrowed 12-Bolt, 4.10 Gears, Spool, Moser 33 Spline
http://www.marsh-racing.com/harrys_camaro-1.htm
Blown 427 BBC, TH400 w/Brake, Back-Half Ladderbar
Narrowed 12-Bolt, 4.10 Gears, Spool, Moser 33 Spline
http://www.marsh-racing.com/harrys_camaro-1.htm
Re: Dash fabrication
You da man!!!!!!! Thats cool
Blackhoodmafia!!!!
1972 Nova SS
572 C.I. BBC
Best to date: 1/8
et: 5.28
mph: 134
new wt. 3340 lbs
1972 Nova SS
572 C.I. BBC
Best to date: 1/8
et: 5.28
mph: 134
new wt. 3340 lbs
Re: Dash fabrication
pro70z28 wrote:Sure, no problem. Money is no object....right?
Yep, money is no object. Supernova takes care of all my bills, just send them to him
1969 ProStreet Camaro RS Best 9.75@139 1.46 60'
Blown 427 BBC, TH400 w/Brake, Back-Half Ladderbar
Narrowed 12-Bolt, 4.10 Gears, Spool, Moser 33 Spline
http://www.marsh-racing.com/harrys_camaro-1.htm
Blown 427 BBC, TH400 w/Brake, Back-Half Ladderbar
Narrowed 12-Bolt, 4.10 Gears, Spool, Moser 33 Spline
http://www.marsh-racing.com/harrys_camaro-1.htm
Re: Dash fabrication
can you get me 1 to harry just say you need 2 one for each hand lol
best to date N/A 8.91@153
psca westcoast heads up racing open comp
67 Camaro RS/SS
BBC Powerglide 4800 stall 4.11 29.5x10.5W
http://www.chpdragracing.com
psca westcoast heads up racing open comp
67 Camaro RS/SS
BBC Powerglide 4800 stall 4.11 29.5x10.5W
http://www.chpdragracing.com
Who is online
Users browsing this forum: No registered users and 0 guests