Winter Upgrades....
Moderator: John_Heard
- Bruce69Camaro
- Posts: 1799
- Joined: Thu Jul 23, 2009 11:07 am
- Location: PA
Winter Upgrades....
Ok, what is on everyone's "To Do" list over the winter?
I added a two step ( thanks Ray), rewired all my controls, getting ready to pull the tranny and put in a transbrake (thanks Don) and I'll be set for the new season.
My 60's area terrible, so I'm hoping the brake will help, but a stall change may be needed????
I also got on the side a forward facing air pan setup for Ray's car, which I'm going to have fun fabricating this thing up for him.
Then I can say, when he picks up a tenth, that's all because of me, but Ray will say it's all because of him....LOL
I never win with him!
Anyhow, my goal that I'm shooting for is 10.0's by the end of next season and I'm hoping it will happen, but any 10's will be a win, win situation in my book.
I added a two step ( thanks Ray), rewired all my controls, getting ready to pull the tranny and put in a transbrake (thanks Don) and I'll be set for the new season.
My 60's area terrible, so I'm hoping the brake will help, but a stall change may be needed????
I also got on the side a forward facing air pan setup for Ray's car, which I'm going to have fun fabricating this thing up for him.
Then I can say, when he picks up a tenth, that's all because of me, but Ray will say it's all because of him....LOL
I never win with him!
Anyhow, my goal that I'm shooting for is 10.0's by the end of next season and I'm hoping it will happen, but any 10's will be a win, win situation in my book.
Those who think they know it all have no way of finding out they don't.........
- John_Heard
- Site Admin
- Posts: 5734
- Joined: Thu May 12, 2005 11:20 am
- Location: Resume Speed, Kansas
- Contact:
Re: Winter Upgrades....
We're debating that right now, trying to decide if we should destroke the engine so the car will be X275 legal or not. Technically it's only a few races around here that run those rules, so doesn't really make sense as the crank will be about $2k. We're going to freshen engine, rings, bearings, new rods, etc.
Would like to get some more weight out of the car, problem is we're at the point where anything significant will not be cheap. Probably work on the nitrous system a bit to see if we can get some more out that too.
Would like to get some more weight out of the car, problem is we're at the point where anything significant will not be cheap. Probably work on the nitrous system a bit to see if we can get some more out that too.
My 1971 X275 Nova | Facebook
Re: Winter Upgrades....
2 grand for a crank ? Whose crank is that ?John_Heard wrote:We're debating that right now, trying to decide if we should destroke the engine so the car will be X275 legal or not. Technically it's only a few races around here that run those rules, so doesn't really make sense as the crank will be about $2k. We're going to freshen engine, rings, bearings, new rods, etc.
Would like to get some more weight out of the car, problem is we're at the point where anything significant will not be cheap. Probably work on the nitrous system a bit to see if we can get some more out that too.
1969 ProStreet Camaro RS Best 9.75@139 1.46 60'
Blown 427 BBC, TH400 w/Brake, Back-Half Ladderbar
Narrowed 12-Bolt, 4.10 Gears, Spool, Moser 33 Spline
http://www.marsh-racing.com/harrys_camaro-1.htm
Blown 427 BBC, TH400 w/Brake, Back-Half Ladderbar
Narrowed 12-Bolt, 4.10 Gears, Spool, Moser 33 Spline
http://www.marsh-racing.com/harrys_camaro-1.htm
- John_Heard
- Site Admin
- Posts: 5734
- Joined: Thu May 12, 2005 11:20 am
- Location: Resume Speed, Kansas
- Contact:
Re: Winter Upgrades....
That's a rough cost for a Callies Magnum & balancing
My 1971 X275 Nova | Facebook
-
- Posts: 158
- Joined: Fri Oct 11, 2013 7:59 pm
- Location: Mountville PA
Re: Winter Upgrades....
Like Bruce said, I am finally after 11 years of having a cowl hood, going to try a forward facing airpan. I have never ran a rear facing pan on this car because so many people have said they just did not make a noticeable difference. Hopefully the ram effect from the front will be enough to pick this thing up some. I am also trying to see if I can swing 4 new shocks and rear springs for the car. The current rears are single adjustable Strange shocks, and Koni SPA-1 shocks in the front. The goal is a double adjustable Strange for the rear and a single adjustable Strange for the front.
And if it picks up a tenth it will be all because of me. If it doesn't pick up a tenth, that will be because of Bruce. So he will get credit too!!!!
And if it picks up a tenth it will be all because of me. If it doesn't pick up a tenth, that will be because of Bruce. So he will get credit too!!!!
Re: Winter Upgrades....
Going to Dyno the motor, new alternator wire, new heavier master disconnect switch, get a shock mount moved (spring rubs the frame). Other than that, just some nut and bolt checks, systems tests, and any other things I need to be race ready in the spring.
73 Vette, moly back half
Pump gas 496
Two Pro Systems 950's
Chance 6000 converter
Pump gas 496
Two Pro Systems 950's
Chance 6000 converter
Re: Winter Upgrades....
Is the Magnum that much better than the Dragonslayer ? Whats the difference ? I've been looking at the Dragonslayer as a possibility for my new build.John_Heard wrote:That's a rough cost for a Callies Magnum & balancing
1969 ProStreet Camaro RS Best 9.75@139 1.46 60'
Blown 427 BBC, TH400 w/Brake, Back-Half Ladderbar
Narrowed 12-Bolt, 4.10 Gears, Spool, Moser 33 Spline
http://www.marsh-racing.com/harrys_camaro-1.htm
Blown 427 BBC, TH400 w/Brake, Back-Half Ladderbar
Narrowed 12-Bolt, 4.10 Gears, Spool, Moser 33 Spline
http://www.marsh-racing.com/harrys_camaro-1.htm
-
- Posts: 158
- Joined: Fri Oct 11, 2013 7:59 pm
- Location: Mountville PA
Re: Winter Upgrades....
Realistically how much power are you looking to make?wikd69 wrote:Is the Magnum that much better than the Dragonslayer ? Whats the difference ? I've been looking at the Dragonslayer as a possibility for my new build.
- John_Heard
- Site Admin
- Posts: 5734
- Joined: Thu May 12, 2005 11:20 am
- Location: Resume Speed, Kansas
- Contact:
Re: Winter Upgrades....
I believe the magnum is the same forging, but with more lightening work done to it.
My 1971 X275 Nova | Facebook
Re: Winter Upgrades....
1000+ HP maybe ? I just bought a new stripped 871 competition blower and I'm probably going to end running injection on top of a 540. I don't really know what sort of power I'll end up making but the build will be an 8.5:1 @ 14+ lbs of boost. This isn't like a turbo or even a procharger build - the horsepower with this roots system is immediate and brutal. You can make bigger horsepower with a big turbo build but I've heard it referred to as 'soft' power cuz it comes on more gradually than the roots stuff.bracketchev1221 wrote:Realistically how much power are you looking to make?wikd69 wrote:Is the Magnum that much better than the Dragonslayer ? Whats the difference ? I've been looking at the Dragonslayer as a possibility for my new build.
1969 ProStreet Camaro RS Best 9.75@139 1.46 60'
Blown 427 BBC, TH400 w/Brake, Back-Half Ladderbar
Narrowed 12-Bolt, 4.10 Gears, Spool, Moser 33 Spline
http://www.marsh-racing.com/harrys_camaro-1.htm
Blown 427 BBC, TH400 w/Brake, Back-Half Ladderbar
Narrowed 12-Bolt, 4.10 Gears, Spool, Moser 33 Spline
http://www.marsh-racing.com/harrys_camaro-1.htm
-
- Posts: 158
- Joined: Fri Oct 11, 2013 7:59 pm
- Location: Mountville PA
Re: Winter Upgrades....
The dragonslayer will be fine then. A compstar crank could probably hold what you want to do if you stay around 1000.
- Mike Peters
- Posts: 930
- Joined: Wed Oct 12, 2005 1:48 pm
- Location: Wichita, KS
Re: Winter Upgrades....
I've read good feedback on a few message boards about Howard's crankshafts. Forged in the U.S. at Louisville Forging and machine finished by Callies. Reading the description in the Competition Products description, their Pro Max version sounds like the same features as the Callies Magnum only less expensive.
Howards Pro Max 4340 Crankshaft 4.5" stroke $1,499.95
100% American Made! Starting with the finest high purity 4340 aircraft quality alloy. Many manufacturers state they use 4340, but very few use the same quality. There is a difference! Forged by the experts in American crankshaft forgings, Louisville forge in Kentucky (again, only a few can state this). These forgings have high quantities of nickel and chromium, which insures strength and long service life. These forgings are shipped to the leader in high performance crankshaft machining, Callies Performance Products. They are machined to the highest specifications, with roundness within 60 millionths and taper being held to within .0003" on all rod and main diameters. All journals have .125" Tru-Form fillet radii. 1" Angalite lightening holes in all rod throws. Callies "Deep Case" hardening produces a wear layer that remains intact even if reground .010" under (other cranks have a hardness depth as little as .003"). Journals are micro-finished to 5 microns or better. The best forgings, the best machining, and the best hardening. Which crank will you run? Requires chamfered bearings.
Callies Magnum Plus Crankshaft 4.5" stroke $1,753.00
The next standard in high performance crankshafts. They feature shaped and profiled counterweights for enhanced windage reduction. Of course as all Callies cranks they use high purity 4340 alloy forging, close tolerance machining, and heat-treat. All throws have Angalite lightening holes and pin arms profiled. Small block cranks also feature gun drilled mains for additional weight savings. Typical big block weighs 68-74 pounds. Requires chamfered bearings.
Howards Pro Max 4340 Crankshaft 4.5" stroke $1,499.95
100% American Made! Starting with the finest high purity 4340 aircraft quality alloy. Many manufacturers state they use 4340, but very few use the same quality. There is a difference! Forged by the experts in American crankshaft forgings, Louisville forge in Kentucky (again, only a few can state this). These forgings have high quantities of nickel and chromium, which insures strength and long service life. These forgings are shipped to the leader in high performance crankshaft machining, Callies Performance Products. They are machined to the highest specifications, with roundness within 60 millionths and taper being held to within .0003" on all rod and main diameters. All journals have .125" Tru-Form fillet radii. 1" Angalite lightening holes in all rod throws. Callies "Deep Case" hardening produces a wear layer that remains intact even if reground .010" under (other cranks have a hardness depth as little as .003"). Journals are micro-finished to 5 microns or better. The best forgings, the best machining, and the best hardening. Which crank will you run? Requires chamfered bearings.
Callies Magnum Plus Crankshaft 4.5" stroke $1,753.00
The next standard in high performance crankshafts. They feature shaped and profiled counterweights for enhanced windage reduction. Of course as all Callies cranks they use high purity 4340 alloy forging, close tolerance machining, and heat-treat. All throws have Angalite lightening holes and pin arms profiled. Small block cranks also feature gun drilled mains for additional weight savings. Typical big block weighs 68-74 pounds. Requires chamfered bearings.
"If winning was easy, losers would be doing it"
Re: Winter Upgrades....
I think that's the same crank dad uses in the 59/dragster engine.
73 Vette, moly back half
Pump gas 496
Two Pro Systems 950's
Chance 6000 converter
Pump gas 496
Two Pro Systems 950's
Chance 6000 converter
Re: Winter Upgrades....
Don't forget new longer rods or taller compression height pistons to make up for the stroke loss.John_Heard wrote:That's a rough cost for a Callies Magnum & balancing
- John_Heard
- Site Admin
- Posts: 5734
- Joined: Thu May 12, 2005 11:20 am
- Location: Resume Speed, Kansas
- Contact:
Re: Winter Upgrades....
It's time to put in new rods, that's the only reason I'm even considering it now.
Those Howard cranks sound pretty good. Having trouble finding anyone that's used one though.
Todd good to have you back on here...
Those Howard cranks sound pretty good. Having trouble finding anyone that's used one though.
Todd good to have you back on here...
My 1971 X275 Nova | Facebook
Who is online
Users browsing this forum: No registered users and 9 guests