leaf spring relocation kit
Moderators: David Lemmond, Dave Morgan
- John_Heard
- Site Admin
- Posts: 5734
- Joined: Thu May 12, 2005 11:20 am
- Location: Resume Speed, Kansas
- Contact:
Stock frame, there is no need to change the rear frame rails even though that's what it says in the CE catalog. The only modifications to the frame are notching where the front spring hanger sets.
My 1971 X275 Nova | Facebook
Beyond,
How far in did you mount your sliders?
Is it centered (front to back) near the stock rear mount?
It looks like a sweet setup.
I'm putting a set of detroit speed & engineering wheel tubs on my
'72 nova. I just bought the tubs because i'm going to run my
Caltracs w/the split mono leafs. I bought the CE offset hangers,
but don't want to raise the ride height. I'm going to try to fit a
set of M/T ET drag 29.5-10.5/15's.
Any help would be greatly appreciated, Thanks.
How far in did you mount your sliders?
Is it centered (front to back) near the stock rear mount?
It looks like a sweet setup.
I'm putting a set of detroit speed & engineering wheel tubs on my
'72 nova. I just bought the tubs because i'm going to run my
Caltracs w/the split mono leafs. I bought the CE offset hangers,
but don't want to raise the ride height. I'm going to try to fit a
set of M/T ET drag 29.5-10.5/15's.
Any help would be greatly appreciated, Thanks.
-
- Posts: 17
- Joined: Sat Jun 02, 2007 11:14 pm
- Location: z-town,la.
- Contact:
shocks
beyond,
I was wondering what kind of shocks those are on your car.
I was wondering what kind of shocks those are on your car.
it's no little pony it's a krazy horse
68' stang W/ 525 bbc,glide
68' stang W/ 525 bbc,glide
- John_Heard
- Site Admin
- Posts: 5734
- Joined: Thu May 12, 2005 11:20 am
- Location: Resume Speed, Kansas
- Contact:
Those are Afco's, I'm getting ready to switch it over to Santhuff's for this year.
My 1971 X275 Nova | Facebook
- gearjammer
- Posts: 228
- Joined: Tue May 17, 2005 7:57 am
- Location: Michigan
- Contact:
I did the same as BeyondBeyond wrote:Stock frame, there is no need to change the rear frame rails even though that's what it says in the CE catalog. The only modifications to the frame are notching where the front spring hanger sets.
shadetree quote: How far in did you mount your sliders?
Is it centered (front to back) near the stock rear mount
Mine are installed 90* to the rear end (straight back) the location of the slider will depend on your leaf spring, if its a 1" drop spring the spring will be flatter which will require the slider to be farther back than stock.
John Calvert recommends that you install the slider so that the center of the rear spring eye is 1" - 1 1/2" from the back of the slider while resting on the ground.
Phil aka Gearjammer
JPR Racing
1972 Nova
Drag Radial
JPR Racing
1972 Nova
Drag Radial
John Calvert recommends that you install the slider so that the center of the rear spring eye is 1" - 1 1/2" from the back of the slider while resting on the ground.[/quote]
Thanks Gearjammer that's a big help.
What is the best way to fab a mount for the slider?
I was thinking of a plate or square tubeing welded
from the bottom of the stock frame rail to the
floor pan.
Thanks
Thanks Gearjammer that's a big help.
What is the best way to fab a mount for the slider?
I was thinking of a plate or square tubeing welded
from the bottom of the stock frame rail to the
floor pan.
Thanks
- gearjammer
- Posts: 228
- Joined: Tue May 17, 2005 7:57 am
- Location: Michigan
- Contact:
Travis
Here are te links
http://www.afabcorp.com/AFCO_Dynatech_U ... all-joints
http://www.jegs.com/webapp/wcs/stores/s ... _763938_-1
Upper Control Arms Bushings # 921-20078 "JEGS"
Lower Control Arm Bushings # 921-20076LW "JEGS"
Upper Ball Joint # 921-20037LF "JEGS"
Lower Ball Joint # 921-20033LF "JEGS"
call me if you need any more info Travis
Here are te links
http://www.afabcorp.com/AFCO_Dynatech_U ... all-joints
http://www.jegs.com/webapp/wcs/stores/s ... _763938_-1
Upper Control Arms Bushings # 921-20078 "JEGS"
Lower Control Arm Bushings # 921-20076LW "JEGS"
Upper Ball Joint # 921-20037LF "JEGS"
Lower Ball Joint # 921-20033LF "JEGS"
call me if you need any more info Travis
Phil aka Gearjammer
JPR Racing
1972 Nova
Drag Radial
JPR Racing
1972 Nova
Drag Radial
Who is online
Users browsing this forum: No registered users and 5 guests